Publicité
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product
.
Please
carry
out
the
steps in
the order
set
out
in
these
instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
Safety advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
2
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance
on
your product.
Do
not
attempt
to assemble the product
in
windy or wet conditions.
Do
not
attempt
to assemble the product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children
away
from the assembly
area.
When using
a
stepladder or power tools, make
sure
that
you
are
following
the manufacturer's
safety advice.
Do
not climb or stand on the
roof.
Do
not hang or
lay
on the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on
the roof
can make
it unsafe to stand below or nearby.
If
color
was
scratched
during
assembly it
can be
fixed.
Cleaning
instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before
starting
assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and
have
a
solid
base such
as
concrete or asphalt.
Sort the parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep
all
small parts (screws etc.) in
a
bowl
so
they do
not get
lost.
Please
consult your
local
authorities if
any
permits
are
required prior to constructing the product.
The
drawings
in
this manual
are
designed for Arcadia 4300 (12'x
14'),
Arcadia 5000 (12'x
16'),
Arcadia 6400 (12'x
21')
products
+ 0.7
or
2.1
Extension
Kits.
Please
note that content
list refers
only to one
set
of
2
pole extensions.
During Assembly
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and
assistance.
Attention
During assembly
use
a
soft surface below the parts to avoid scratches and damages.
M
Steps
Step
1: The
Arcadia Alpine Kit
can be set at
two optional
heights.
Step 6: After completing the assembly
of
the
Arcadia Alpine
Kit,
please
revert back to the
Arcadia assembly instructions and continue the assembly from Steps
3
-
41.
Step
7: Make sure
the poles'
foot
pads are
leveled prior to
tightening
the
screws,
use
a
spirit
level.
Step 8: Make
sure
the product
is
square by measuring the diagonals.
Make
sure
the product
is
level by using
a
spirit
level.
Use
the supplied
screws
and plugs for
concrete or asphalt foundation.
Tighten
all screws at
the end of assembly.
Note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
Publicité
