Publicité
Les langues disponibles
Les langues disponibles
G Operating instructions
Bluetooth
headset with NFC
®
Item no. 1384373
Intended use
The product is intended for the wireless transmission of voice and music from mobile
phones, tablets, laptops and other devices.
Connection with the headset is realised via Bluetooth
The power is supplied by a permanently integrated LiPo rechargeable battery (non-
replaceable), which can be recharged through the supplied micro-USB cable from
USB port or the USB power adapter.
A driver installation is not necessary.
Carefully read the entire operating instructions which contain important information
about operation and use. Observe all safety instructions!
Package contents
• Bluetooth
headset
®
• Micro-USB cable
• Operating instructions
Safety instructions
D amages caused by failure to follow these operating instructions will void
the warranty/guarantee. We do not assume any liability for any resulting
damage!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void!
Dear customer,
the following safety instructions and hazard warnings are intended not only
to protect your health but also to protect the device. Please read the follow-
ing points carefully:
• For safety and licensing reasons (CE), unauthorised conversion and/or
modification of the product is not permitted.
• The product does not require maintenance. Maintenance or repair work
may be performed only by qualified personnel or a specialised repair
shop. The product contains no parts that require servicing. Therefore, do
not open it.
• Protect the product from direct solar radiation, strong heat, cold and vi-
brations or mechanical loads.
• The product must not get damp or wet, as this will destroy it. There is also
risk of fire and explosion from the integrated rechargeable battery.
• The product is not a toy and does not belong in the hands of children. The
product contains small parts and rechargeable batteries.
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
• If the product shows visible damages, do not use it any longer. Contact a
professional or a qualified workshop.
• If you are not going to use the product for a long time (putting it e.g. to
storage), recharge the battery every 3 months at the latest to prevent deep
discharge. In the event of a deep discharge, the built-in LiPo rechargeable
battery will be permanently damaged!
• If you have any questions that are not answered in these operating in-
structions, please contact our technical support centre or consult a pro-
fessional.
All manuals and user guides at all-guides.com
.
®
Controls and display
1
Ear bow (detachable; right- and
left-compatible)
2
Push button to answer and end
calls
3
NFC sensor
4
LED
5
Increase volume (+); next track
6
Reduce volume (-); previous track
7
Earphone
8
Microphone
9
Micro-USB port for charging
Getting started
a) Charging the headset
Before you start using the headset, the built-in rechargeable battery should be fully
charged. First charging before getting started lasts for about 2 hours. During the next
battery charge the process lasts for about 90 minutes.
To charge the headset, proceed as follows.
• Remove carefully the small rubber protection flap (9) to make the USB charge con-
nector accessible.
• Plug the supplied micro-USB cable into the micro-USB port (9). Pay attention to the
correct orientation when inserting the plug.
• Connect the normal USB plug type A to a USB port e.g. of a computer or a USB
power adapter.
• The charging process starts immediately. The red LED (4) lights up.
• The LED goes out once the charging process is over.
When the battery power is low, the LED (4) flashes every 15 seconds in red.
b) Switching headset on and off
• To switch on the headset press and hold the answer-call button (2) for approx.
4 seconds until the LED flashes twice in blue.
• To switch off the headset press and hold again the answer-call button (2) for
approx. 4 seconds until the LED flashes twice in red.
c) Pairing the headsets via Bluetooth
The pairing procedure is explained in reference to an Android
However, this feature works similarly with any other device, which supports Blue-
tooth
. If anything goes wrong during configuration, just switch the headset off and on
®
again. To link the headset with your smartphone, proceed as follows.
• If the headset is switched on, switch it out first.
• To proceed to the pairing mode, press and hold the answer-call button (2) for approx.
7 seconds until the LED quickly flashes in alternating blue and red.
• Now enable Bluetooth
on your smartphone. You can find the function in the Con-
®
nections section under Settings.
• Start search for new Bluetooth
®
• Once the device "TWNT-BH803" is displayed, tap it to pair the headset with your
smartphone. If the pin number is prompted enter 0000.
In some smartphones it is also required to create connection additionally after pair-
ing. In that case, tap the device "TWNT-BH803" again.
Observe also the operating instructions for your smartphone.
• Once the pairing is successfully completed, the pairing mode ends up automatically.
Now, the headset is in standby mode and the LED (4) flashes briefly every 5 seconds
in blue.
To connect your headset later with your smartphone again, you need to
switch on the headset and activate Bluetooth
the connection is not automatically created just tap again on the device
"TWNT-BH803", which is already paired.
®
-based smartphone.
TM
devices.
in your smartphone. If
®
Publicité
