Télécharger Imprimer la page

ITC IJS2000 Manuel De L'utilisateur page 2

Publicité

Les langues disponibles

Les langues disponibles

IMPORTANT SAFETY INSTRUCTIONS
ALL
READ
INSTRUCTIONS BEFORE USING THIS TOOL
WARNING!
= Do not connect the black negative clamp to the negative battery terminal.
= Do not expose this unit to rain or moisture.
= Keep this equipment out of the reach of children.
= Improper use of this unit may result in bodily injury such as burns or blindness.
This unit contains a sealed, lead-acid battery that should be kept at full charge.
Recharge this unit when first received, immediately after each use, and once a
month if not used.
CAUTION: When using electric tools, machines or equipment, basic safety pre-
cautions should always be followed to reduce the risk of fire, electric shock,
and personal injury.
GENERAL SAFETY INSTRUCTIONS
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp,
wet, or poorly lit locations. Don't expose your tool to rain. Keep the work area
well lit. Don't use tools in the presence of flammable gases or liquids.
3. KEEP CHILDREN AND BYSTANDERS AWAY. All children should be kept
away from the work area. Don't let them handle machines, tools or extension
cords. Visitors can be a distraction and are difficult to protect from injury.
4. USE THE RIGHT TOOL. Don't force a small tool or attachment to do the work
of a larger industrial tool. Don't use a tool for a purpose for which it was not
intended.
5. DO NOT ABUSE THE CORD. Never carry your tool by the cord or pull on the
cord to unplug it. Protect the cord from potential sources of damage: heat, oil
& solvents, sharp edges, or moving parts. Replace damaged cords
immediately.
6. WHEN WORKING OUTDOORS, USE AN OUTDOOR-RATED EXTENSION
CORD. An extension cord rated for outdoor use must be marked "W-A" or "W".
7. DO NOT EXPOSE ELECTRICAL POWER TOOLS TO MOISTURE. Rain or
wet conditions can cause water to enter the tool and lead to electric shock.
8. ENSURE THE EXTENSION CORD YOU USE IS OF SUFFICIENT GAUGE
FOR ITS LENGTH.
Amps
7.62 m
from Tool Nameplate
(25') long
0 - 5 amps
16 ga.
5.1 - 8 amps
16 ga.
8.1 - 12 amps
14 ga.
12.1 - 15 amps
12 ga.
15.1 - 20 amps
10 ga.
9. STORE IDLE EQUIPMENT. Store equipment in a dry area to inhibit rust. Equip-
ment also should be in a high location or locked up to keep out of reach of
children.
10. DRESS PROPERLY. Don't wear loose clothing or jewelry; they can be caught in
moving parts. Protective, non-electrically conductive gloves and non-skid foot-
wear are recommended when working. Wear protective hair covering to contain
long hair and keep it from harm.
11. USE EYE PROTECTION. Use a full-face mask if the work you're doing produces
metal filings, dust or wood chips. Goggles are acceptable in other situations.
Wear a clean dust mask if the work involves creating a lot of fine or coarse dust.
12. DON'T OVERREACH. Keep proper footing and balance at all times. Do not
reach over or across machines that are running.
2
All manuals and user guides at all-guides.com
Recommended Minimum Wire Gauge for Extension Cords
15.24 m
22.86 m
30.48 m
(50') long
(75') long
(100') long
16 ga.
16 ga.
14 ga.
16 ga.
14 ga.
12 ga.
14 ga.
12 ga.
10 ga.
12 ga.
10 ga.
10 ga.
10 ga.
10 ga.
Do Not Use
45.72 m
60.96 m
(150') long
(200') long
12 ga.
12 ga.
10 ga.
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
!
!

Publicité

loading

Ce manuel est également adapté pour:

028112