AEG BKS18BL2 Traduction De La Notice Originale page 25

Investigate and take corrective actions to eliminate the cause of
blade binding.
If a saw blade binds, it may walk up or kickback from the workpiece
as the saw is restarted.
Large panels tend to sag under their own weight.
Supports must be placed under the panel on both sides, near the
line of cut and near the edge of the panel.
set blades produce narrow kerf causing excessive friction, blade
binding and kickback.
cutting, it may cause binding and kickback.
kickback.
Lower guard function
If the saw is accidentally dropped,the lower guard
may be bent. Raise the lower guard with the retracting handle and
make sure it moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
Lower guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
other sawing, the lower guard should operate automatically.
coasting blade will cause the saw to walk backwards, cutting
whatever is in its path. Be aware of the time it takes for the blade to
stop after switch is released.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Do not use any abrasive wheels.
Use only blade diameter(s) in accordance with the markings.
Identify the correct saw blade to be used for the material to be cut.
Use only saw blades that are marked with a speed equal or higher
than the speed marked on the tool.
Use only saw blades recommended by the manufacturer, which
conform to EN 847-1, if intended for wood and analogous materials.
Wear a dust mask.
Clamp the workpiece with a clamping device. Unclamped
Dirty blade guards may limit proper operation of the product,
compressed air to ensure there is no accumulation of saw dust.
Wear proper eye and respiratory protection.
Raise the lower guard by the lever and ensure that the lower guard
returns to the original position. If the lower guard does not function
properly. Stop using the product and have it repaired.
immediately if it stalls. Do not turn on the product again while it is
still stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the product stalled and rectify this,
paying heed to the safety instructions.
Remove the battery pack before starting any work on the product.
Unsharpened or improperly
For all
An unprotected,
ENGLISH
The circular saw is intended for rip-cutting and cross-cutting of wood
or similar materials up to a maximum depth of 68 mm. The product
can make straight or bevelled cuts between 0 and 56 degrees.
The product is to be used with the base of the tool in contact with
the workpiece. It should only be used in a dry, well-lit, and well-
ventilated area.
The product is designed for handheld use. The product is not to be
mounted onto a workbench. Do not use the product for cutting metal
or masonry.
Do not use the product for any other purpose.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING!
product damage due to a short circuit, never immerse your tool,
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
Do not dispose of used battery packs in the household refuse or
protect our environment.
Use only AEG chargers for charging AEG battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers, and store them only
in dry rooms. Keep battery packs and chargers dry at all times.
Battery packs that have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged
after use.
To obtain the longest possible battery life, remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and
away from moisture.
• Store the battery packs in a 30% - 50% charged condition.
• Every six months of storage, charge the pack as normal.
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
If the product does not start up again, the battery pack may have
discharged completely. Recharge the battery pack.
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national, and international provisions and regulations.
• Batteries can be transported by road without further requirement.
• Commercial transport of lithium-ion batteries by third parties is
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
• Ensure that the battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that the battery pack is secured against movement within
the packaging.
• Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
25