GE LED19GX24q-H/827 Guide D'installation

LED 4-pin plug-in Lamps
BEFORE YOU BEGIN
To install the LED 4-pin plug-in lamps, please read the entire installation guide carefully.
The LED 4-pin plug-in lamp is not intended to be used with dimmers and emergency fixtures.
The lamp can only be used with approved ballasts. See ballast compatibility list at: https://products.gecurrent.com/sites/products.
currentbyge.com/files/documents/document_file/LED-Plug-In-Compatibility-Sheet.pdf. Use of unapproved ballasts or bypassing the
original ballast will result in safety and regulation issues.
WARNING: Risk of Fire or Electric Shock. Suitable for Dry and Damp Locations. The installation must be done by qualified electricians
and all safety instructions must be followed to avoid a risk of injury or property damage.
Installation Instructions
Switch off power to
1
the fixture.
Note: If the lamp flickers, flashes or fails on installation, the ballast is not
compatible with the lamp. Remove the lamp and check the ballast compatibility
list again or contact Current for technical support at 1-800-327-0097.
RISK OF ELECTRIC SHOCK - SUITABLE FOR DAMP LOCATIONS. Direct replacement for cfq42w/gx24q CFL
lamps only. Not for use in totally enclosed luminaires. Not for use with dimmers. For use only with compatible
ballasts. See list at: https://products.gecurrent.com/sites/products.currentbyge.com/files/documents/
document_file/LED-Plug-In-Compatibility-Sheet.pdf.
Not intended for use with emergency exit fixtures or emergency exit lights. Not for use in totally enclosed fixtures. Suitable for damp locations, do not
use were directly exposed to water. FOR USE ONLY WITH COMPATIBLE BALLASTS. See list at: https://products.gecurrent.com/sites/products.currentbyge.
com/files/documents/document_file/LED-Plug-In-Compatibility-Sheet.pdf. This device complies with Part 18 of the FCC Rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including
interference that may cause undesired operation. Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment. NOTE: This product complies with Part 18 of the FCC Rules but may cause interference to radios, televisions, wireless
telephones, and remote controls. Avoid placing this product near these devices. If interference occurs, move the product away from the device or plug
either into a different outlet. Do not install this product near maritime safety equipment or other critical navigation or communication equipment
operating between 0.45-30 MHz. This device complies with CAN ICES-005B.
Remove the existing fluorescent
2
lamps from the fixture and
dispose of them properly based
on local regulations.
www.gecurrent.com
© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under
license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
LEDL096 (Rev 11/17/20) Enovia - A-1028166
Installation Guide LEDL096 | A-1028166
42W horizontal lamp
LED19GX24q-H/827
LED19GX24q-H/830
LED19GX24q-H/835
LED19GX24q-H/840
Check the socket condition in the
3
fixture. If damaged or corroded, replace
it with a new one. Insert Current LED
4-pin lamps. For horizontal application,
rotate the lamp so the diffuser is facing
towards the fixture opening. Warning:
Sockets in poor condition may result
in bad electrical contact, base arcing or
other safety issues. Note: In two lamps
condition, be sure to use Current LED
4-pin lamps in both sockets. Do not use
one CFL and one LED lamp together on
the same ballast as the ballast may shut
down.
CAUTION
42W vertical lamp
LED19GX24q-V/827
LED19GX24q-V/830
LED19GX24q-V/835
LED19GX24q-V/840
Restore power to
4
fixture and check for
proper operation.