Metabo HS 18 LTX BL 55 Notice Originale page 10

en ENGLISH
6.2 Removing and inserting the battery pack
Hold the machine when removing and
inserting the battery pack so that the on/off
switch cannot be unintentionally pressed.
Removing:
Press the battery pack release (8) button and
remove the battery pack (11).
Inserting:
Slide in the battery pack (11) until it engages.
Check quick stop:
Switch machine on briefly and then off again.
Have the machine repaired if braking time is clearly
lengthened.
Do not reach in the battery pack recess when
inserting the battery pack.
7. Use
7.1 Switch-on lock, switching on and off
(safety two-hand operation):
To switch on the machine, the activation button (16)
in the control panel (12) must be operated. This will
put the machine in operating condition for 120s.
LED (15) lights up green.
• Switching on: Press the switch (18), press the
frame switch (6).
• Switching off: Release the switch (6) or (18). The
operating condition extends automatically if (6)
and (18) are pressed.
Thanks to the Quick stop, the cutting blades come
to a standstill within 0.2 seconds.
Have the machine repaired if braking time is
clearly lengthened.
7.2 Using the rotating handle for ergonomic
working
• Pull release (19) in direction of arrow (see fig. P 2)
• Put the rotating handle into the desired position
and wait until it engages automatically.
Check if the handle has engaged safely.
•For safety reasons, the release (19) cannot
be operated while the button (18) is activated.
Should this be possible due to a defect in the
machine, have the machine repaired.
• Do not reach into the rotation area while adjusting
the angle of the rear handle.
7.3 Status LED battery pack (14)
The machine has a battery control display (14).
Below a residual charge of approx. 20%, the LED
starts flashing orange. Remedy: Charge battery
pack or replace soon.
8. Cleaning
The cutting blade needs to be cleaned after each
use.
Before cleaning:
Switch off the machine. Remove battery pack
(11) from the machine.
10
Wear protective gloves.
Remove contamination, leaf debris etc.
(e.g. with a brush or cloth)
After cleaning: Treat cutting blades with Metabo
machine care oil 6.30474 or Pump Spray 6.30475
(biologically degradable).
9. Troubleshooting
LED fault display (13)
if the machine cannot be switched on, the LED fault
display (13) shows possible fault causes.
1. Fault display (13) lights up permanently red:
• Blade is blocked: Remove battery pack, remove
blockage.
• Battery pack defective: Replace battery pack.
• Machine defective: Have machine repaired.
2. Fault display (13) flashes red
• Battery pack empty: Charge or replace battery
pack.
• Battery pack or machine too hot: Remove battery
pack, let machine and battery pack cool down.
10. Maintenance
It is advisable to have blunt cutting blades
sharpened in a specialist workshop. Check cutting
blades regularly for damage and have them
repaired in a specialist workshop immediately if
necessary.
f
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
A Chargers: ASC 55, ASC 145, etc.
Order no.: 627044000ASC 55
Order no.: 627378000ASC 145
etc.
B Battery packs:
Order no.: 625367000 4.0 Ah (LiHD)
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625026000 2,0 Ah (Li-Power)
Order no.: 625027000 4,0 Ah (Li-Power)
Order no.: 625028000 5,2 Ah (Li-Power)
etc.
C Hedge trimmer care oil (biologically
degradable), can (1 litre)
Order no.: 630475000
D Hedge trimmer care oil (biologically
degradable), Pump Spray can (0.3 litre)
Order no.: 630474000
For a complete range of accessories, see
www.metabo.com or the catalogue.