Kenmore 110.2613 Série Guide D'utilisation Et D'entretien page 5

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

CYCLE SIGNAL
Use this option to adjust volume of the signal that sounds
at end of cycle� The Cycle Signal is a helpful reminder to
remove items from washer as soon as the cycle has
completed�
To turn Button Sounds either On or Off:
While washer is on, touch and hold Cycle Signal for 3
seconds� Washer will make a single beep when the process
is complete�
NOTE:
• Cycle Signal button will still operate, even if you turned
the button sounds off.
• Whatever your preferences are, they remain in effect
through a power loss�
• The Default setting for button sounds is ON.
7
CYCLE OPTIONS
You may add or remove options for each cycle� Note that
not all options can be used with all cycles, and some are
preset to work with certain cycles�
PREWASH
Use this option to add an extra agitation and soak time
to the beginning of any cycle to break up tough stains�
DEEP FILL
Will add the most amount of water for large or bulky
loads� Items need to move freely� Tightly packing the
load can lead to poor cleaning performance, and may
increase wrinkling and tangling�
TWO RINSES
This option can be used to automatically add a second
rinse to most cycles�
NOTE: If you want to Drain and Spin only, select the Rinse
& Spin cycle; then touch to turn off the Two Rinses option.
FABRIC SOFTENER
This option must be set to "On" if using fabric softener�
It ensures that fabric softener is added at the correct
time in the rinse for even distribution�
STEAM TREAT for Steam models or STAIN BOOST for
Non-Steam models
This option provides enhanced cleaning action for tough
stains� It will add additional agitation and soak time to
the cycle�
CYCLE STATUS LIGHTS INDICATOR
8
The Cycle Status Lights show the progress of a cycle� At each
stage of the process, you may notice sounds or pauses that
are different from traditional washers.
DELAY
When the Delay Wash is selected, this light will come on
to indicate your washer is set-up to run a delayed wash�
ADD A GARMENT
You may place additional clothing in the wash when the
Add a Garment indicator is lit without sacrificing wash
performance� Touch START/PAUSE once� The Lid Lock light
will turn off. Open the washer lid, add garments, and
close the lid� Touch and hold START/PAUSE to restart�
WASH
You will hear the motor and washplate moving the load�
It is normal for some of the load to be above the water
line� Low-water cleaning means concentrated cleaning�
Rather than diluting detergent as done in an agitator-style
washer, this washer delivers the detergent directly to the
soils. The motor sounds may change at different stages
in the cycle� The wash time is determined by the selected
Soil Level�
RINSE
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load� Fabric softener will
be added if the Fabric Softener option was selected�
SPIN
The washer spins the load at increasing speeds for proper
water removal, based on the selected cycle and spin
speed�
COMPLETE
Once the cycle is complete, this light will come on�
Remove the load promptly for best results�
LID LOCKED
To allow for proper load sensing and spinning, the lid
will lock and the Lid Locked light will turn on� This light
indicates that the lid is locked and cannot be opened�
If you need to open the lid, touch START/PAUSE/Unlock
Lid� The lid will unlock once the washer movement has
stopped� This may take several minutes if the load was
spinning at high speed� Touch and hold START/PAUSE/
Unlock Lid again for up to 3 seconds to resume the cycle�
5

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

110.2713 série110.2813410 série110.2913410 série

Table des Matières