Télécharger Imprimer la page

Palram GARDA CLOSED GARDEN GAZEBO Instructions De Montage page 4

Masquer les pouces Voir aussi pour GARDA CLOSED GARDEN GAZEBO:

Publicité

IMPORTANT
Please read these instructions carefully before you start to assemble this product .
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
Safety advice
For safety purposes we strongly recommend the product to be assembled by at least two people.
Some parts may have sharp edges. Please be careful when handling components. Always wear
gloves, eye protection, and long sleeves when assembling or performing any maintenance on
your product.
Do not attempt to assemble the product in windy or wet conditions.
Do not attempt to assemble the product if you are tired, have taken drugs,
medications or alcohol, or if you are prone to dizzy spells.
Dispose of all plastic bags safely - keep them away from children's reach.
Keep children away from the assembly area.
When using a stepladder or power tools, make sure that you are following
the manufacturer's safety advice.
Do not climb or stand on the roof.
Do not hang or lay on the profiles.
Heavy articles should not be leaned against the poles.
Keep roof and gutters clear of snow, dirt & leaves.
Heavy snow load on the roof can make it unsafe to stand below or nearby.
If color was scratched during assembly it can be fixed.
Cleaning instructions
In order to clean the product, use a mild detergent solution and rinse with
cold clean water.
Do not use acetone, abrasive cleaners, or other special detergents to clean the panels.
Clean the product once assembly is complete.
Before starting assembly
Choose your site carefully before beginning assembly.
The ground surface must be perfectly flat and leveled and have a solid base such as concrete,
asphalt, deck etc.
Sort the parts and check against the content parts list.
Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do
not get lost.
Please consult your local authorities if any permits are required prior to constructing the product.
During Assembly
MWhen encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
When encountering these icons, you are requested to either keep the screws slightly loose or
to fully tighten the screws.
Attention
During assembly use a soft surface below the parts to avoid scratches and
damages.
Please note you install the panels with the UV protected side out (marked with
"THIS SIDE OUT") remove plastic film before inserting panels and locking in place.
If the panels received with the product are Bronze, please remove only the plastic sticker
as panels are locked in place.
Step 1: The ground surface must be perfectly flat and leveled and have a solid base such
as concrete, deck etc. At this stage a circle should be marked for the hexagon corners to be
placed later.
Step 7: Attach the hexagon's corners to the marked circle, make sure they are flat and level
prior to connecting to the base. Make sure you use the suitable screws and plugs for your
type of base.
Step 18+19: If you find it slightly difficult to slide the roof panels in, it will be easily done
by 2 people. One on a step ladder near the peak and the other pushing from the bottom.
Please note you install the panels with the UV protected side out (marked with "THIS SIDE
OUT") remove plastic film before inserting panels and locking in place.
If the panels received with the product are Bronze, please remove only the plastic sticker as
panels are locked in place.
Step 20: Please decide upon the entrance direction. The next assembly steps will show
doors with the locking done from outside (later on, we will show the assembly of the other
doors which are to be locked from inside)
* Please note, the direction and placement of the doors in the following steps
Step 26+27: Please assemble the rest of the doors, pay close attention to the direction.
The locking of the doors should be done from inside.
Tighten all screws at the end of assembly.
Note:
Anchoring this product to the ground is essential to its stability and rigidity.
It is required to complete this stage in order for your warranty to be valid.

Publicité

loading