Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ICAR by ORTEA NEXT
.
COD
DESCRIPTION
A10
Voltage THD too high
A11
Current THD too high
A12
Maintenance requested
14
COMMANDS MENU
The commands menu allows executing some occasional operations like reading peaks resetting, counters clearing, alarms
reset, etc. If the Advanced level password has been entered, then the commands menu allows executing the automatic
operations useful for the device configuration. The following table lists the functions available in the commands menu,
divided by the access level required.
access the Commands menu.
the selected command. The RPC 5LGA regulator shows
end of the countdown, the command is executed, while if the key is released before the end, the command is
COD.
COMMAND
C01
RESET MAINTENANCE
C02
RESET STEP COUNT
C03
RESET STEP TRIMMING
C04
RESET STEP HOURS
C05
RESET MAX VALUES
C06
RESET WEEKLY TPF
C07
SETUP TO DEFAULT
C08
SETUP BACKUP
C09
SETUP RESTORE
15
WI-FI DONGLE USE
The WI-FI dongle offers WI-FI access point capability for connection to PC, Tablet or Smartphone. In addition to this function
it also offer the possibility to store and transfer a block of data from/to the RPC 5LGA regulator.
Insert the interface WI-FI into the IR port of RPC 5LGA regulator on the front plate. Switch WI-FI dongle on by pressing the
button for 2 sec. Wait until the
At this point the display of the RPC 5LGA regulator shows the first of the 6 possible commands (D1...D6). Press ▲▼to select
the desired command. Press
once again
per confermare, or
CODE
COMMAND
D1
02
SETUP DEVICE
CX
D2
02
SETUP CX
DEVICE
D3
02
CLONE DEVICE
CX
D4
02
CLONE CX
DEVICE
D5
02
INFO DATA CX
D6
EXIT
16
INSTALLATION
RPC 5LGA regulator is designed for flush-mount installation. With proper mounting, it guarantees IP54 front protection.
From inside the panel, for each four of the fixing clips, position the clip in one of the two sliding guide, then press on the clip
corner until the second guide snaps in. Push the clip forward pressing on its side and making it slide on the guides until it
presses completely on the internal surface of the panel.
For the electrical connection see the wiring diagrams in the dedicated chapter and the requirements reported in the technical
characteristics table.
17
INFORMATION & SERVICE
ENABLE
●
●
●
With controller in MAN mode, press
Select the desired command with
PSW
DESCRIPTION
Usr
Reset maintenance service interval.
Adv
Reset step operation counters.
Adv
Reload originally programmed power into step trimming.
Adv
Reset step operation hour meters.
Adv
Reset maximum peak values.
Usr
Resets weekly total power factor history.
Adv
Resets setup programming to factory default.
Adv
Makes a backup copy of user setup parameters settings.
Usr
Reloads setup parameters with the backup of factory settings.
LED becomes orange flashing. Press 3 times consecutively and fast the dongle button.
LINK
to execute the selected command. The unit will prompt for a confirmation (
to cancel. The following table lists the possible commands:
DESCRIPTION
Copies Setup settings from RPC 5LGA regulator to WI-FI dongle.
Copies Setup settings from WI-FI dongle to RPC 5LGA regulator.
Copies Setup settings and working data from RPC 5LGA regulator to WI-FI dongle.
Copies Setup settings and working data from WI-FI dongle to RPC 5LGA regulator.
Shows information about data stored into WI-FI dongle.
Exits from dongle menu.
ICAR by ORTEA NEXT
ORTEA S.p.A
Via dei Chiosi 21 20873 Cavenago B.za (MB) – Italy
Tel. +39 02 9591 7800
www.next.ortea.com
Technical service: tech.cv@icar.com
ALARM RELAY
●
●
●
for 5s. Press
or
. Press and hold for three seconds
? with a countdown.
By pressing and holding the
OK
18 / 40
ALL75 mar19
DISCONNECTION
DELAY
60 s
●
●
60 s
0s
▲
to selecte
. Press
CMD
▲
to execute
▲
key until the
canceled.
?). Press
OK
to
Publicité
Table des Matières
