Bissell POWERFRESH Mode D'emploi page 6

Before you clean
Thoroughly sweep or vacuum floor prior to
cleaning with the PowerFresh™ Steam Mop.
Cleaning hard floors
Your PowerFresh™ Steam Mop is designed
to clean hard flooring such as ceramic tile,
vinyl, laminate, marble, stone and sealed
hard wood floors. Use of your PowerFresh™
Steam Mop on waxed or some unwaxed
floors may result in a diminished glossiness.
The PowerFresh™ Steam Mop is not for
use on unsealed wood floors. For best
results test in an inconspicuous area
and check the care instructions from
your flooring manufacturer.
To sanitize an area of your floor, place
the hard floor cleaner over the spot for
a minimum 15 seconds using continuous
steam, but no longer than 20 seconds using
continuous steam. For larger areas, overlap
mop head placement.
1. Plug the unit in and wait 30 seconds for
it to heat up. Choose the level of steam
to clean your floor: Low (delicate floors),
Medium (regular cleaning), High (durable
floors or sticky messes). Begin cleaning by
slowly passing the unit over the floor surface.
2. To thoroughly clean dried-on sticky spots
place the scrubby pad on the steam mop.
Then press and lock the Easy Scrubber brush
into place and slowly move the brush over
the sticky spot to remove.
3. When the PowerFresh™ Steam Mop
stops emitting steam, unplug the unit.
Simply remove the water tank, refill,
and continue cleaning.
Carpet Refresher Attachment
This accessory is recommended for the
refreshing of carpets. Once the steam mop
is cradled in the carpet refresher attachment,
it will easily glide over the carpet.
NOTE: Always be sure a mop pad is in
place before placing in carpet refresher
attachment. Only white mop pads should
be used with the carpet attachment. Do
not use carpet attachment on spots or
stains, or glide it over the same spot for
longer than 20 seconds.
1. Place the swivel mop head, with mop pad
attached, in the carpet refresher attachment.
NOTE: The PowerFresh™ Steam Mop rests
in the carpet refresher attachment and may
not stay attached to the swivel mop head.
It is meant to glide over the carpet.
2. Fill water tank with water. Begin refreshing
your carpet or rug by depressing the
Steam-on-Demand trigger while pushing the
PowerFresh™ Steam Mop in a forward and
backward motion, releasing steam as you go.
www.BISSELL.com
6
All manuals and user guides at all-guides.com
3. When you have finished refreshing your
carpet or rug, unplug the steam mop and
remove from the carpet or rug.
NOTE: Move the PowerFresh™ Steam
Mop and carpet refresher attachment in a
continuous motion until you are finished.
This product is not intended to be used as
a carpet cleaner, only a carpet refresher
or deodoriser. Never attempt to use the
PowerFresh™ Steam Mop on carpet without
the carpet refresher attachment in place. DO
NOT leave the mop in a stationary position.
Maintenance & Care
When you're done
1. Unplug power cable from electrical socket.
2. Carefully remove the mop pad using the
Quick Release™ tab from the mop head. The
mop pad and lower assembly may be hot.
Remove Spring Breeze Freshening Disc from
mop pad.
3. Any water remaining in the water tank
should be emptied prior to machine storage.
4. Mop pad can be machine washed in warm
water. Use only liquid detergents. Do not use
fabric softeners or bleach. For best results,
air dry.
5. Wrap power cable around quick
release cable wrap on back of PowerFresh™
Steam Mop.
6. Wipe all surfaces of PowerFresh™ Steam
Mop with a soft cloth. Store upright in a
protected, dry area.
mopping a large floor area. The steam mop generates hot steam,
so when depressing the trigger to apply steam, ensure the steam
mop is moving continuously. The trigger does not need to be
depressed at all times. Prolonged application of steam in one area
increases the risk of damage to the surface treatment on timber
floors. Check with your timber floor treatment application specialist
prior to steam mop operation. Regular foot traffic and direct
sunlight will wear down timber floor surface treatment, making it
more susceptible to steam damage. Exercise extreme care when
using the steam mop on timber flooring.
Tinted plates on foot may get hot while steam mop is in use.
Do not touch while hot.
Upright storage of the PowerFresh™ Steam Mop with a wet mop
pad may result in the formation of white marks on your floor.
To remove the white marks, clean area with vinegar.
Exercise extreme care when using the steam
mop on timber flooring. Ensure the steam mop is
thoroughly tested in an inconspicuous area prior to
Never put descaling, aromatic, alcoholic, or
detergent products into the steam cleaner, as this
may damage it or make it unsafe for use.