Manuels Connexes pour Osburn Matrix-I
Sommaire des Matières pour Osburn Matrix-I
- Page 1 MATRIX DOOR HANDLE REPLACEMENT INSTRUCTIONS INSTRUCTIONS DE REMPLACEMENT DE POIGNÉE DE PORTE MATRIX 46372AF 2023-11-02...
- Page 2 KIT CONTENT / CONTENU DE L’ENSEMBLE Washer 1/4-20 x 3/4'’ bolt Boulon 1/4-20 x 3/4'’ Rondelle #30093 (A) #30187 (B) Door handle mechanism Shim Mécanisme de poignée de porte Espaceur #SE65082 (D) #PL75754 (C) #8-32 x 5/8’’ Mechanical screw Wooden handle Vis mécanique #8-32 x 5/8’’...
- Page 3 REQUIRED TOOLS / OUTILS REQUIS Power driver equipped with : • 3/8’’ hexagonal socket • #2 Robertson bit Visseuse électrique équippée de : • Embout hexagonal 3/8’’ • Embout Robertson #2 • #2 Robertson screwdriver • #2 Philips screwdriver • Tournevis Robertson #2 •...
- Page 4 DOOR HANDLE MECHANISM INVERSION (IF APPLICABLE) INVERSION DU MÉCANISME DE POIGNÉE DE PORTE (SI APPLICABLE) If the loading door opens from the right side of the unit, the door handle mechanism from this kit must be reversed prior to replacement procedure. Si la porte de chargement s’ouvre par le côté...
- Page 5 CURRENT DOOR HANDLE MECHANISM REMOVAL DÉMONTAGE DE LA POIGNÉE DE PORTE D’ORIGINE 1. Using a wood screw and a power driver, slightly drive into the wooden dowels to pull them out of the door handle. Unscrew the screws retaining the door handle to the mechanism.
- Page 6 2. Unscrew bolts (A) and washers (B) to remove the door handle mechanism from the door. Throw away the bolts and the washers. Dévisser les boulons (A) et les rondelles (B) pour retirer le mécanisme de poignée de la porte. Jeter les boulons et rondelles. 46372AF 2023-11-02...
- Page 7 DOOR HANDLE MECHANISM INSTALLATION INSTALLATION DU MÉCANISME DE POIGNÉE DE PORTE 1. Place the shim (C) under the bracket of the handle mechanism (D). Secure the mechanism inside the door with 2 washers (B) and 2 bolts (A) provided in the kit. Placer l’espaceur (C) sous le support du mécanisme de poignée (D).
- Page 8 2. Secure the wooden handle (E) with 2 screws (F). Insert 2 wooden dowels (G) in the chambered holes using a rubber mallet. Fixer la poignée de bois (E) avec 2 vis (F). Insérer 2 goujons de bois (G) dans les trous chambrés à...
- Page 9 DOOR LATCH ACCESS INSTRUCTIONS (MATRIX INSERT) INSTRUCTIONS D’ACCÈS À LA BARRURE DE PORTE (MATRIX ENCASTRABLE) 1. The door latch can be adjusted at any time from the front. However, for better access to the door latch mechanism, follow the procedure: Remove the wooden handle (H) and screw (I) from the air controller.
- Page 10 DOOR LATCH ACCESS INSTRUCTIONS (MATRIX STOVE) INSTRUCTIONS D’ACCÈS À LA BARRURE DE PORTE (MATRIX POÊLE) 1. Remove the top decoration (N) and raise the top panel assembly (O). Remove the first side panel (P) located to the left side of the unit. Retirer la décoration supérieure (N) et soulever le panneau supérieur assemblé...
- Page 11 HANDLE AND LATCH ADJUSTMENT AJUSTEMENT DE LA POIGNÉE ET DE LA BARRURE 1. Slightly loosen both bolts (Q). -Detail A- Dévisser légèrement les boulons (Q). -Détail A- 2. Lock the door handle onto the loosened latch. Fermer la poignée de porte sur la barrure desserrée. 3.
- Page 12 7. Open the door and squeeze a strip of paper between the door and the combustion chamber. Close the door and pull the paper strip and seek for resistance. Repeat the action all around the door opening. If the paper strip pulls out without any resistance, the door doesn’t seal airtight.
- Page 13 This document is available for free download on the manufacturer’s website. It is a copyrighted document. Resale is strictly prohibited. The manufacturer may update this document from time to time and cannot be responsible for problems, injuries, or damages arising out of the use of information contained in any document obtained from unauthorized sources.