JUNO J6SLC RGBW MW Instructions D'installation page 3

• Unless individual product specifications deem otherwise: Maximum ambient temperature is 90°C. Do not operate fixture at
temperatures higher than this.
• Unless individual product specifications deem otherwise: Never mount in places where fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all
installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• There are no user serviceable parts inside the unit. Do not rewire, reconfigure, or modify the unit or attempt any repairs
yourself. Additionally, field replacement of the LED assembly or lamps is not allowed by UL standards at this time. In the
unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative.
• Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.
• Verify that power distribution system has proper grounding. Lack of proper earth ground can lead to fixture failure and may
void warranty.
•
CAUTION RISK OF WIRING PRODUCT DAMAGE
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply
with one of the following Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC's and IC's RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s)
used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must
not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation
distance will be maintained between the device (excluding its handset) and users.
Cet appareil est conforme aux limites d'exposition au rayonnement RF stipulées par la FCC et l'IC pour une utilisation dans un
environnement non contrôlé. Les antennes utilisées pour cet émetteur doivent être installées et doivent fonctionner à au moins 20
cm de distance des utilisateurs et ne doivent pas être placées près d'autres antennes ou émetteurs ou fonctionner avec ceux-ci. Les
installateurs doivent s'assurer qu'une distance de 20 cm sépare l'appareil (à l'exception du combiné) des utilisateurs.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada's license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
1) L'appareil ne doit pas produire de brouillage;
One Lithonia Way · Conyers, GA 30012 · Phone 1-(800)705-7378
Visit us at
© 2023 Acuity Brands Lighting, Inc
INSTALLATION INSTRUCTIONS
www.acuitybrands.com/juno-recessed
.
Juno Smart LED RGBW Speaker LED Trim Kit
912-00386-001 REV B
DATE 05/2023
3
PAGE |