Publicité
Les langues disponibles
Les langues disponibles
Safety
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential for
personal injury:
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which are
important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
1. Read this manual carefully. Failure to follow these
instructions could cause serious bodily injury and/or
property damage.
2. Check your local codes before installing. You must
comply with their rules.
3. Connect the pump to a separate circuit with no other
appliances on the circuit. Consult a licensed electrician
for all wiring.
NOTICE: This pump does not require a connection to a
main stack vent, per the National Standard Plumbing Code
(NSPC) 2003 Section 11.7.9.
Hazardous voltage. Can shock, burn or
cause death. Unplug pump before working on it.
DESCRIPTION
This pump is designed to be used with a sink where a grav-
ity drain line is not available. Attach the pump to the drain
tail piece; the pump will start when water begins to drain.
Uses include basement laundry sinks, wet bars and utility
sinks.
SPECIFICATIONS
Power supply required ....................................115V, 60 HZ.
Liquid Temp. Range....................... 32° – 120°F (0° – 50°C)
Individual Branch Circuit Required (min.)..............15 Amps
Pump Inlet...........................................................1-1/2" NPT
Pump Discharge .................................................1-1/4" NPT
Fire or explosion hazard. Do not use in
explosive atmospheres. Pump fresh water only with this
pump. Use with salt water or brine will void the warranty.
INSTALLATION
(SEE FIGURES 1 AND 2)
Electric Shock Hazard. Plug pump into a
properly grounded, GFCI protected outlet. Do NOT plug in
the pump until after it is completely installed. Do not
remove or modify the grounding pins on the plugs.
Sink Bottom with Drain Port;
Sink Bottom with Drain Port;
Tail Piece integral with Sink
Tail Piece integral with Sink
A
A
1
1
2
2
For easier maintenance,
For easier maintenance,
use 2 short sections of
use 2 short sections of
pipe connected by a
pipe connected by a
1-1/2" Solvent Union.
1-1/2" Solvent Union.
3
3
1-1/2" Pump
1-1/2" Pump
Inlet Port
Inlet Port
1-1/4" Pump
1-1/4" Pump
Discharge
Discharge
Fittings Supplied:
Fittings Supplied:
A
A
Sink Drain Screen
Sink Drain Screen
B
B
1-1/4" NPT x 1-1/4" Slip Check Valve
1-1/4" NPT x 1-1/4" Slip Check Valve
C
C
1-1/4" NPT Ball Valve
1-1/4" NPT Ball Valve
Purchase Separately:
Purchase Separately:
1
1
1-1/2" NPT x 1-1/2" Slip Female Adapter
1-1/2" NPT x 1-1/2" Slip Female Adapter
2
2
1-1/2" Schedule 40 PVC Pipe, to fit
1-1/2" Schedule 40 PVC Pipe, to fit
3
3
1-1/2" NPT x 1-1/2" Slip Male Adapter
1-1/2" NPT x 1-1/2" Slip Male Adapter
4
4
1-1/4" NPT Galvanized Nipple (to fit)
1-1/4" NPT Galvanized Nipple (to fit)
5
5
1-1/4" NPT Galvanized Union
1-1/4" NPT Galvanized Union
6
6
1-1/4" NPT x 1-1/4" Male Adapter
1-1/4" NPT x 1-1/4" Male Adapter
7
7
1-1/4" Schedule 40 PVC Pipe, to fit
1-1/4" Schedule 40 PVC Pipe, to fit
8
8
1-1/4" Socket to Socket 90° Elbow
1-1/4" Socket to Socket 90° Elbow
9
9
1-1/4" Schedule 40 PVC Pipe to Drain
1-1/4" Schedule 40 PVC Pipe to Drain
PVC Pipe Cement
PVC Pipe Cement
Teflon Tape
Teflon Tape
1-1/2" Plastic Solvent Union
1-1/2" Plastic Solvent Union
(For Drop Pipe – Optional)
(For Drop Pipe – Optional)
NOTE: Be careful to avoid cross-threading;
NOTE: Be careful to avoid cross-threading;
Use only a plastic-compatible pipe-threading
Use only a plastic-compatible pipe-threading
compound or teflon tape when connecting
compound or teflon tape when connecting
threaded fittings to plastic adapters.
threaded fittings to plastic adapters.
Figure 1: Typical method of mounting the pump.
4
4
5
5
6
6
7
7
Qty.
Qty.
1
1
1
1
1
1
Qty.
Qty.
1
1
1
1
1
1
1
1
1
1
2
2
4
4
1
1
As Needed
As Needed
As Needed
As Needed
As Needed
As Needed
2
9
9
B
B
C
C
6
6
7
7
8
8
Publicité
