Publicité
Les langues disponibles
Les langues disponibles
Natural Gas (France/Belgium):
This dryer is also certified for France/Belgium for use with
G20/G25 gases (20 mbar/25 mbar) with appropriate
conversion. No attempt should be made to convert this
appliance from the gas specified on the gas rating label for use
with a different gas without consulting the serving gas supplier.
Gas conversion must be done by a Whirlpool authorised gas
service technician. Conversion kit, part number (W10181947)
is available for purchase from your dealer. Full instructions are
supplied with the kit.
Supply line requirements:
Provide a rigid gas supply line to the dryer location. It should
be minimum 12.5 mm (1/2") ID. When acceptable to the gas
supplier and local codes, 10 mm (3/8") ID rigid supply line may
be used for lengths under 6.1 m (20'). Pipe-joint compounds
resistant to the action of L.P. gas must be used.
NOTE: For installation in Australia and New Zealand, refer to
AS/NZS 5601 for pipe sizing details. All piping is to be in
accordance with AS/NZS 5601.1 – Gas Installations.
Gas connection to the dryer itself should be made by means
of a flexible gas hose suitable for the appliance and gas
category in accordance with national installation regulations. If
in doubt, contact the gas supplier. It should be minimum
10 mm (3/8") ID.
A means of restraint should be used between the dryer and the
wall to avoid straining of the rigid gas supply when the dryer
is moved. An appropriate length of chain and a wall hook is
recommended.
The dryer gas inlet connection is a 3/8" NPT thread. An adapter
is supplied for conversion to standard ISO.228-1 thread
(3/8" BSP).
Check for leaks by using an approved noncorrosive leak
detection solution. Bubbles will show a leak. Correct any leak
found. A pressure measurement tapping is provided on the gas
valve within the dryer, accessible after removal of the lower
front panel.
The dryer must be disconnected from the gas supply piping
system during any pressure testing of that system
ELECTRIC DRYER
ELECTRICAL
REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances.
This dryer is supplied without an electric cord and plug. It
must be connected by a Whirlpool authorised service person
to a single-phase electricity supply at the voltage shown on
the data plate, using a suitable fixed wiring installation in
accordance with local and national wiring regulations.
A 3-wire circular cord of minimum conductor size 2.5 mm
■
cross-section area should be used.
A 25 A (minimum) supply fuse should be used, and a switch
■
with a clear OFF marking having a contact separation in
both poles that provides full disconnection under
over-voltage category III conditions must be incorporated
into the fixed wiring in accordance with local wiring
regulations by a Whirlpool authorised service person.
The dryer should be positioned so that the disconnection
switch is clearly visible and easily accessible to the user.
This disconnection switch also provides the function of an
emergency stop control for the user.
A cord clamp bushing is provided on the dryer, and should
■
be tightened on completion of wiring. The electrical mains
terminals are located behind the small rear access panel
(terminal block cover), and connections should be made
in accordance with the terminal markings. Remember to
replace the terminal access panel (terminal block cover).
NOTE: In accordance with the European EMC Directive
(2014/30/EU), the maximum electrical supply system
impedance to which the electric dryer should be connected
is declared to be 0.054 Ω + 0.034 Ω.
NOTE: Electrical safety standards: The manufacturer has
chosen compliance with IEC/EN.60335 standards as the
most appropriate for this product.
WARNING
Electrical Shock Hazard
This is a 3-wire appliance which must be earthed.
Securely tighten all electrical connections.
Failure to follow these instructions could result in death,
fire, or electric shock.
If codes permit and an additional ground bond wire is used, it
is recommended that a qualified electrician determine that the
ground bond path is adequate.
Recommended Earthing Method
It is your responsibility to contact a qualified electrical installer
to ensure that the electrical installation is adequate and in
conformance with all local codes and ordinances.
Do not earth to a gas pipe.
2
11
Publicité
