ARIETE Duetto DOUBLE PERFORMANCE 6437 Mode D'emploi page 16

switch (Fig. 9). When the steam ready light (S) turns on, the steam is ready.
When first used, the iron may give out a little smoke: this transitory effect is perfectly normal and will disappear
very soon.
On first use, after filling the tank, it is necessary to adjust the temperature control knob (M) over the symbol (
the steam button (L) Fig. 11 until the iron does not produce steam (about one minute) Fig. 13. The iron is now ready for
use. Before applying a jet of steam to the article to be ironed, release two or three good jets of steam towards the floor to
stabilise the steam flow.
Warning!
Do not release steam when the iron is standing on its grille rest (E).
The boiler is now automatically filled by a pump which produces a noise (vibration) lasting a few seconds every time it is
activated. A decrease in the steam output may occur soon after the pump starts operating: it is perfectly normal and after a
few seconds the steam will again be regular.
If the iron has not been used for a long time, it is advisable to keep it in a horizontal position and send a few shots of steam
to the floor in order to stabilize the jet before ironing.
steam adjustment
The appliance is equipped with a regulator (U) which allows the steam output to be adjusted from a minimum to a maximum
according to ironing requirements.
shot of steam
For ironing thicker fabrics and for a potent anti-crease action in vertical position, it is possible to operate the turbo steam
function. Make sure that there is water is in the tank (C) and in the iron tank (M). Place the control knob (U) on the MAX
value. Wait for the steam ready light (S) to turn on. Set the ironing temperature by turning the adjustment knob (M) past the
•••
symbol ( ). Wait for the indicator lamp (O) of the iron to turn off. Press deeply the steam button (L) from 3 to 5 seconds
(Fig. 11). If the steam supply button (L) is operated continuously for more than 30 seconds, drops of water may come from
the steam holes in the plate of the iron. It is recommended that the button (L) is used for shorter periods.
continuous steam
Turn the steam adjustment knob (U) to MAX. Wait for the steam ready light (S) to turn on. Set the ironing temperature by
turning the adjustment knob (M) past the symbol (
temperature is reached, press the steam button (L) Fig. 12. The cursor (K) will lock the button, making the jet of steam
exit continuously and steadily. To unlock the button (L) and stop the continuous jet, press the cursor (K) forward (Fig. 14).
Temperature selection
First check whether the fabric has a label containing ironing instructions and compare the symbol with the instructions which
follow. If there is no label with instructions, but you know the type of material, follow the instructions below.
Note that the table refers to fabrics not treated with sizing agents or similar products; if they have been, you can also iron
at a lower temperature.
When you change the temperature by turning the adjustment knob (M), the light (O) will turn on and stay on until the iron
reaches the new temperature.
filling the boiler during use
always check the level of water in the tank while you are ironing.
add enough water to the tank so that the water level is always visible. do not go past the maX level.
If the tank remains without water, you will notice a vibration and a louder noise. Turn off the appliance by pressing the
switches (T) and (V). unplug it from the electric outlet.
Warning!
Always turn off the appliance and remove the power cable plug from the socket-outlet before filling the tank with
water.
Add water directly in the tank (Fig. 7). Insert the plug into the electrical outlet and turn on the appliance again.
If the appliance is not switched off promptly, overheating of the pump could cause a momentary stoppage of the appliance.
Therefore it is necessary to switch off the appliance and fill the tank. Wait about an hour for the appliance to cool down and
resumes normal operation.
spray button
Make sure there is water in the tank of the iron (N). Press the spray button (J). To enable this feature you may need to press
the spray button repeatedly (Fig. 15).
16
All manuals and user guides at all-guides.com
•••
). Wait for the indicator lamp (O) of the iron to turn off. When the
•••
) and press