Publicité
This product is compatible with the following RS485 access
control readers:
AXIS A4011-E Reader
HID iCLASS® RW100: 6101CG40000, 6101CGM0000,
6101CK40000, 6101CK40002, 6101CK40100,
6101CK403C0, 6101CKM0000, 6101CKM0002,
6101CKM0203; RW300: 6111CG40000, 6111CG400C0,
6111CGM0000, 6111CK40000, 6111CK4000Z,
6111CKM0000; RW400: 6121CG40000, 6121CGM0000,
6121CK40000, 6121CK40003, 6121CK40007-G3.0,
6121CK4000D-G3.0, 6121CKM0000; R40:
6122CKP00P0, 6122CKP05P0, 6122CKP06P0; RWK400:
6131CG4020000, 6131CK4000000, 6131CK4000014,
6131CK4000300, 6131CK4020000, 6131CKM000000,
6131CKM000214; RK40: 6132BKP00Q709-G3.0,
6132CKP000009, 6132CKP000011, 6132CKP000700-G3.0,
6132CKP000709-G3.0, 6132CKP001009, 6132CKP001011,
6132CKP00P000, 6132CKP00P009, 6132CKP00P709-G3.0,
6132CKP00Q709-G3.0, 6132CKP030014, 6132CKP060514,
6132CKP06P009, 6132CKP06P609, 6132CKP070209;
RW150: 6141CG40000, 6141CGM0000, 6141CK40000,
6141CKM0000; R15: 6142CKP000Z, 6142CKP00P0,
6142CKP0100; RWKL550: 6171BK4000000,
6171BK4000009, 6171BK4000014, 6171BK4000214,
6171BK4000500, 6171BK4040Z14, 6171BK4060000,
6171BK4060209, 6171BK4060Z09, 6171BK4061000,
6171BKM000000, 6171BKM000200, 6171BKM000300,
6171BKM040400; RWKLB575: 6181BK4000000,
6181BK4000009, 6181BK4000014, 6181BK4000022,
6181BK406C009;
HID Smartid®: 8031DSAP
HID pivClass® R10-H: 900LHRNAK00000,
900LHRTAK00000, 900NHRNAK00000, 900NHRTAK00000,
900PHRNAK00000, 900PHRTAK00000, 910LHRNAK00000,
910LHRTAK00000, 910NHRNAK00000, 910NHRTAK00000,
910PHRNAK00000, 910PHRTAK00000, 920LHRNAK00000,
920LHRTAK00000, 920NHRNAK00000, 920NHRTAK00000,
920PHRNAK00000, 920PHRTAK00000, 921LHRNAK00000,
921LHRTAK00000, 921NHRNAK00000, 921NHRTAK00000,
921PHRNAK00000, 921PHRTAK00000; RPKCL40-P:
923LPRNAK00000, 923LPRTAK00000, 923NPRTAK00000,
923PPRNAK00000, 923PPRTAK00000
TM
Aptiq
: M11, MTK15, MTMSK15, MT15, MTMS15
For information about which compatible RS485 access
control readers have been verified by UL, see Requirements
for Compliance with UL294 6th Edition on page 4 .
Requirements for Compliance with UL294 6th Edition
This section contains information and instructions required
for UL compliance. To make sure the installation is UL
compliant, follow the instructions below in addition to the
general information and instructions provided throughout
this document. In cases where pieces of information
contradict each other, the requirements for UL compliance
always replace general information and instructions.
Supported readers
•
Compatibility with the following RS485 readers has
been verified by UL: HID iClass RK40, HID SmartID 8031
DSHM, and AptiqQ MTMSK15.
Safety instructions
•
The Axis product shall be installed and serviced by a
factory trained professional.
•
The Axis product shall be installed within the protected
premises (secured area).
•
The Axis product shall be mounted indoors. Outdoor
use has not been evaluated or approved by UL.
All manuals and user guides at all-guides.com
•
•
•
•
Specifications
•
•
•
All interconnecting devices shall be UL Listed and Class
2 low-voltage power limited.
All wiring methods shall be performed in accordance
with NFPA70, local codes and authorities having
jurisdiction.
When the Axis product has reached the end of its
useful life, dispose of it according to local laws and
regulations. The product should not be disposed of
together with household or commercial waste. See
Disposal and recycling.
Battery
-
The 3.0 V lithium battery used by
the Axis product is a UL Recognized
component. (Type: BR2032,
diameter: 20 mm (0.78 in),
manufacturers: Rayovac,
Panasonic). The following battery
type is also a UL Recognized
component: Type CR2032,
manufacturers: Fuji, Maxell,
Renata, Varta, Panasonic, JHIH
-
Users shall not replace the battery.
If the battery needs replacing, a
factory trained service professional
shall contact Axis support
at www.axis.com/techsup for
assistance.
-
Used batteries shall be disposed
of according to local laws and
regulations, which may vary from
state to state. Waste BR/CR
lithium cells are neither listed
nor exempted from the USEPA
hazardous waste regulations. Waste
lithium batteries can be considered
reactive hazardous waste if there is
a significant amount of unreacted,
or unconsumed lithium remaining.
For information about how to
dispose of used lithium batteries,
contact your local authority for
waste disposal.
Operating conditions
-
Temperatures
0 °C to 50°C (32 °F to 122 °F).
Wire area
-
UL Listed or R/C AWM wires that
have an conductor gauge range of
AWG 22–14 shall be used.
-
The minimum conductor gauge for
connection between the power
sourcing equipment (PSE) or power
injector and the powered device
(PD) is 26 AWG.
Connectors
-
This product is not intended for
outside wiring as covered by Article
800 in the National Electrical Code,
NFPA 70.
-
Power connector – For UL security
applications, the product shall be
powered by a UL 294 Listed or
UL 603 Listed Class 2 low-voltage
power limited power supply that
is capable of 4 hours of standby
power.
-
Network connector – Power over
Ethernet (PoE) shall be supplied
Publicité
