Erfal EAM24 Mode D'emploi page 6

Basic settings
B
Only necessary for motor replacement or after factory reset.
For adjusting the end positions see A „Fine adjustment of the end positions"!
If there is an already programmed remote control, continue with G „Remote control and channels".
Confi guring remote control
Press P1 1x run up Release Press STOP 2x runs up and down
for 2s and down P1 for 2s
Set/change direction of rotation
Press UP Moves down Press UP + DOWN 1x run up
for 1s for 2s
and down
Set end positions
C
ATTENTION! Motor moves to continuous operation after longer keystroke! Urgently stop before reaching the end position
and then proceed through a tip..
For adjusting the end positions see A „Fine adjustment of the end positions"
Set upper end position
Press UP Moves up Move to requested Press UP + STOP
for 1s end position for 2s
Set lower end position
Press DOWN Moves Move to requested Press DOWN+ STOP
for 1s down end position for 2s
D Change operation mode to jog mode
Operating in jog mode: The motor moves to continuous operation after 2 sec. of key pressing. Repeat the programming step
to switch back to continuous operation.
1x run up and down
Press UP + DOWN 1x run up Press STOP
for 5s for 2s
and down
2x run up and down
E Change speed
Press UP
for 1s
Press P2
1x run up and down
for 1s
Press DOWN
for 1s
All manuals and user guides at all-guides.com
Next:
Set/change direction
of rotation
Direction of rotation
was successfuly
changed
Next:
Set lower
end position
2x runs up and down
Lower end
position is set
2x runs up and down
Jog mode
Continuous operation
Press UP
1x run up and down 2x run up and down
for 1s
Press DOWN
1x run up and down 2x run up and down
for 1s
Set intermediate positions/ stops
F
Setting custom stop position
Move to the Press 1x run up and
intermediate P2 for 1s
down
stop
Approach custom stop position
Blind will move to the
intermediate stop.
Press
STOP 3s
Remove custom stop position
Press
1x run up and down
P2 for 1s
Remote control and channels
G
Add remote control or channel
A motor can store up to 10 remote control channels, learning further channels is rejected by the motor.
Note: is the already programmed remote control,
A
A
Press
1x run up and down
P2 for 1s
Delete remote control or channel
Note: and are the already programmed remote controls,
A B
A
Press
1x run up and down
P2 for 1s
Factory reset
H
Press 4x runs up and down
P1 for 1s
Malfunctions and troubleshooting
I
Error Cause
faster
a) The battery is empty.
b) The battery is charging, but not moving.
Motor is not
moving
slower
c) The remote control is not trained.
d) P1 programming button is pressed but no reaction.
End positions must be set!
Press 1x run up and Press 2x run up and
STOP for 1s STOP for 1s
down down
Press Press
1x run up and down 1x run up and down
STOP for 1s STOP for 1s
is the new remote control which has to be programmed!
B
A B
Press Press
1x run up and down 2x run up and down
P2 for 1s P2 for 1s
B is the remote control which has to be programmed!
A B
Press Press
1x run up and down 2x run up and down
P2 for 1s P2 for 1s
The motor has been reset
to factory settings
Release
P1
Solution
a) Charge the battery.
b) Battery was deeply discharged, wait for certain state of charge.
c) Follow programming step B.
d) The motor is defect, contact sun protection specialist.
Intermediate
stop is set
Intermediate stop
is removed
Remote control B
has been added
Remote control B
has been deleted