Conrad 75 42 64 Mode D'emploi page 4

Installation
Bolt down the enclosed aerial at the back side of the surveillance camera and align it vertically
upwards for optimum reception.
Drill a hole of 15 mm diameter at the position where you wish to fi x the surveillance camera to
the exterior wall. The hole will be needed to pass the power supply cable to the interior.
Make sure that there are no power supply lines or water pipes at the position behind
the wall where you wish to install the surveillance camera to avoid damage while
drilling the necessary holes!
Fix the camera support to the wall using the screws provided so that you are able to pass the
power supply cable of the surveillance camera through the hole in the wall.
Unfasten the thumb screw on the camera's support until you are able to freely move the thread
to which the surveillance camera will be attached.
Tighten the surveillance camera with the thread at the bottom side of the support.
Move the surveillance camera to the desired position and then tighten the thumb screw again
to fi x the camera in this position.
Connect the surveillance camera to the power supply in the indoor area using the wall plug
transformer provided. The distance between the surveillance camera and the power supply
should not exceed the length of the camera's wall plug transformer cable. Do not use an
extension cable.
Tips & Notes
• Night vision function: The surveillance camera features built-in infrared LEDs which are
turned on automatically at night. At night coloured image reproduction changes into black
and white monochrome representation.
• The surveillance camera provided can be operated with the two following video surveillance
systems:
- 2.4 GHz digital radio DVR monitor set (item no. 754263)
- 2.4 GHz digital radio colour camera and radio receiver with recording function (item no. 754270)
Both systems provide a „masking" function which can be used to excluded certain areas of
the image captured by the camera from the motion detection. For further information, please
read the operating manual of the two above mentioned video surveillance systems.
Handling
• Follow the safety instructions in this operating manual and all other information on installation
and operation.
• The surveillance camera is suitable for installation and operation in outdoor areas (IP66).
The corresponding wall plug transformer (protection class II) may be operated only in indoor
areas.
• Never use the product immediately after it has been taken from a cold room to a warm one.
The condensation that forms might destroy the product. Moreover, there is danger of an
electric shock from the wall plug transformer!
• Leave the product switched off and wait until it has reached room temperature before you use
it. This can possibly take several hours.
• Any maintenance or repair work may only be carried out by authorised personnel.
• If the product is not to be used for a while, unplug the wall plug transformer.
• Avoid the following adverse conditions at the installation location and during transportation:
- Damp or excess air humidity
- extreme cold or heat
- Dust or fl ammable gases, fumes or solvents
- Strong vibration
- Strong magnetic fi elds such as those found in the vicinity of machinery or loudspeakers
Maintenance and Cleaning
The product does not require any maintenance and should never be disassembled for any
reason. To clean the product, use a dry, clean and soft cloth; before cleaning, disconnect the
product from the power supply, unplug the wall plug transformer from the mains socket. Clean
the lens very carefully to avoid scratch marks. Do not use aggressive detergents as these might
cause discoloration of the casing.
All manuals and user guides at all-guides.com
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and the other relevant regulations of the
directive 1999/5/EC.
☞
Disposal
Technical Data
a) Surveillance camera
Max. number of channels ....................................4
Range of wireless data transfer ...........................150 m in open space
Camera resolution ...............................................640 x 480
Transmission frequency.......................................2.4 GHz
Operating temperature ........................................-20 °C to +50 °C
Operating voltage ................................................5 V/DC, 1 A
Current consumption ...........................................IR OFF: 165±20 mA / IR ON: 465±20 mA
Night vision range (IR-LEDs) ...............................5 – 8 m
Protection type .....................................................IP66 (suitable for outdoor use)
Dimensions ..........................................................123 x 65 x 65 mm
b) Wall plug transformer
Power supply .......................................................100 - 240 V AC, 50/60 Hz
Output ..................................................................5 V/DC, 1 A
The Declaration of Conformity (DOC) for this product can be found at:
www.conrad.com
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste! Please dispose of the device when it is no longer of use, according to
the current statutory requirements.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.