Portable Winch PWM600MH Consignes De Fonctionnement/Sécurité page 14

2.2.7 Stopping the engine.
To stop the engine:
1) Release the traction lever if the machine is in motion;
2) Lower the throttle lever to idle position;
3) Turn the switch to the OFF position.
IMPORTANT: If the on/off switch fails, close the choke to stop
the engine.
If you do not intend to start the engine soon and if you need to move
the machine, wait until the blade and all moving parts have stopped
and turn the fuel valve to the OFF position.
3. Usage
ITS COMPACT SIZE AND LOW WEIGHT ALLOW THE 600MH
PERIMETER WIRE MACHINE TO BE EASILY CARRIED IN A
SMALL VEHICLE. IT IS STRONGLY RECOMMENDED THAT YOU TURN THE FUEL VALVE
TO THE OFF POSITION (OFF).
Before each use:
● Check the soil consistency and the deepest possible insertion
depth.
● Check the engine oil level.
● Check the blade attachment.
● Check the attachment of the wire guide.
● Check the tire pressure.
3.1 Installing the perimeter wire spool.
The 600MH TM Perimeter Wire Machine is designed to
accommodate most wire spools provided by the manufacturers of
robot lawnmowers.
IMPORTANT : Four (4) spacers are provided (2 x 6.5 cm and 2 x
3 cm) for centering the spools, the wire boxes or the drum on
the shaft. If necessary, these should be inserted on the left and
right of centering hubs depending on the width of the spool.
3.1.1 Spools mounted on a drum
The hardware provided is suitable for installation of most models up
to 800 metres (according to wire diameter):
1
2
3) Remove the shaft (with the hardware). Then remove the
hardware.
All manuals and user guides at all-guides.com
1) Unscrew the clamping handle and
remove with the flat washer.
2) Lift the shaft while opening the
blocker.
a. Spacer(s);
b. The left centering hub (towards the inside of the spool);
c. The spool (support at the right level depending on its diameter)
on the hub;
d. The right centering hub (towards the inside of the spool);
e. Spacer(s);
f. The rubber washer;
TM
3.1.2 Spools without a drum.
3.1.2.1 Spools that empty through the center.
Some manufacturers supply a spool designed to be emptied through
the center. Two (2) PERIMETER WIRE BOXES 18 cm x 18 cm (part
PWMA-0002) and 22.5 cm x 22.5 cm (part PWMA- 0003), available
as optional accessories for the Perimeter Wire Machine 600MH
accepting this type of spool (up to 17.5 cm or 21 cm in diameter,
depending on the box used).
3.1.2.2 Spools with no defined shape.
Some manufacturers provide wire designed to be wound around the
drum manually. As an optional accessory for the Perimeter Wire
Machine 600MH , a PERIMETER WIRE DRUM (part PWMA-0001)
TM
is available to allow the winding of the wire provided by the
manufacturer.
3.2 Moving the machine to the work zone.
To move the machine to the work zone :
1) Loosen the clamping lever on the
handle;
2) Pivot the handle until it is vertical on
the machine.
3) Lift the support foot in front the
machine.
4) Pull or push the machine to the work
3
area.
4
4) Insert in the desired order
depending on the spool used.
NOTE : Depending on the width of the spool, the
number of spacers used may vary. To center the
spool and avoid a lot of unscrewing, you may
use at your discretion. Adjust the spool holder
as required.
The spacers can also be used as center hubs
.
for some spools
5) Insert the shaft by sliding it into the
slots provided (arch and adjustable
spool support). Return the flat
washer and the clamping handle
to the shaft. Screw in the clamping
handle while applying enough
pressure on the spool so that it
doesn't unwind by itself.
EN
,
TM
4