Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
610GCFFCVR & 610GTFFCVR FURNITURE FEED COVER
FOR CONCRETE FLOOR BOX
Installation Instructions
CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing.
NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes,
communications standards, the following instructions and any instructions included with individual devices.
NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance with the NEC
and CE Code requirements.
Use with CFB6G30 series floor boxes and CFB6FFDIVKIT divider kit.
Use with CFB10G55 series floor boxes and CFB10FFDIVKIT divider kit.
AFTER CONCRETE POUR
1.
Locate floor box, remove temporary concrete covers. CAUTION: Temporary concrete covers are intended to keep
concrete residue from entering box during pour and are not intended to support loads. Replace with permanent
flange/cover immediately after concrete has hardened.
2.
The wiring volume for each service application is the sum of the volume markings in each wiring chamber of the
floor box.
3.
Pull and dress wires.
4.
For single service applications, go to step 6.
5.
For multi service applications, install divider kit CFB6FFDIVKIT (purchased separately) for CFB6G30 series floor
boxes or divider kit CFB10FFDIVKIT (purchased separately) for CFB10G55 series floor boxes. Refer to divider kit
instructions for wireway in the floor box.
6.
Install finished flooring to within 1/8 inch (3.2 mm) of cover opening.
7.
For flush flanges (610GTFFCVR series), attach cover flange [1] to top mounting plate using jack screws [2], See
FIGURE A. To adjust cover flange height, turn jack screws counterclockwise to raise or clockwise to lower.
Sequentially turn four jack screws as needed for proper leveling of flange to floor. The jack screws have a 1-inch
maximum adjustment. Torque screws to 12-15 in-lbs of torque (1.3 - 1.7 N m). DO NOT OVERTIGHTEN.
8.
Seal the gap between the flange and finished floor with electrical grade type RTV silicone sealant to ensure scrub
water tightness, see FIGURE A.
FLUSH FLANGE SHOWN WITH 6 GANG FLOOR BOX
FIGURE
Wiring Device - Kellems
Hubbell Incorporated (Delaware)
Shelton, CT 06484
1-800-288-6000
www.hubbell-wiring.com
PD2928
02/21
2
1
SEAL ALL AROUND
A
ENGLISH
Publicité
Manuels Connexes pour Hubbell 610GCFFCVR
Sommaire des Matières pour Hubbell 610GCFFCVR
- Page 1 610GCFFCVR & 610GTFFCVR FURNITURE FEED COVER FOR CONCRETE FLOOR BOX Installation Instructions ENGLISH CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing. NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes, communications standards, the following instructions and any instructions included with individual devices.
- Page 2 For surface flanges (610GCFFCVR series), apply a 1/4 inch (6.3 mm) thick continuous bead of electrical grade type Type 610GCFFCVR and 610GTFFCVR series furniture feed covers are supplied with 3/4 inch closure plugs [6], 1 inch to RTV silicone sealant around the perimeter on the underside of the cover flange [1]. Attach cover flange [1] to 3/4 inch reducer [7] and 2 inch closure plugs [8], see FIGURE C.
- Page 3 COUVERCLES 610GCFFCVR ET 610GTFFCVR POUR BO TE DE PLANCHER EN B TON DESTIN E L ALIMENTATION DU MOBILIER Directives de montage FRAN AIS ATTENTION - RISQUE DE CHOC LECTRIQUE. D brancher le circuit avant de proc der au montage ou la maintenance.
- Page 4 Les couvercles des s ries 610GCFFCVR et 610GTFFCVR pour alimentation du mobilier sont livr s avec des bouchons de 19 mm [6], Pour les rebords en surface (610GCFFCVR), appliquer un cordon continu de 6,3 mm (1/4 po) de p te calfeutrer la silicone de type RTV pour applications lectriques sur tout le p rim tre int rieur du couvercle [1].
- Page 5 Hubbell Products M xico, S. de R.L. de C.V. garantiza este producto, de estar libre de defectos en materiales y mano de obra por un a o a partir de su compra.
- Page 6 Para las bridas de superficie (serie 610GCFFCVR), aplique un cord n continuo de 6,3 mm (1/4 ) de espesor de sellador de Las cubiertas de alimentaci n para muebles de las series 610GCFFCVR y 610GTFFCVR se suministran con tapones de cierre silicona RTV de grado el ctrico alrededor del per metro en la parte inferior de la brida de la cubierta [1].