Conrad 97 24 30 Mode D'emploi page 3

O P E R A T I N G I N S T R U C T I O N S
DSL Router with Modem
Item no. 97 24 30
Intended Use
The DSL router is intended to be used to establish an Internet connection. It includes an inte-
grated DSL modem.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Router
• Wall plug transformer
• DSL connection cable
• Operating Instructions
Features
• Inbuilt DSL modem
• RJ45 10/100 Mbit network port for connection to a computer or network switch
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warranty
will be void in such cases.
The unauthorised conversion and/or modifi cation of the product is inadmissible be-
cause of safety and approval reasons (CE).
The product is intended for use in dry indoor locations, it must not get damp or wet!
There is a risk of a lethal electric shock!
The design of the wall plug transformer complies with safety class II. As the voltage
source for the wall plug transformer, only a standard power socket (230V~, 50Hz)
connected to the public grid may be used.
The device is not a toy. Keep devices that operate on the mains voltage out of the
reach of children! Therefore, be especially careful when children are around.
Do not carelessly leave the packaging material lying around since it could become a
dangerous plaything for children.
Handle the product carefully, it can be damaged by impacts, blows or by falling from
a low height.
Connection
• The router has a integrated modem; therefore, connect the"LINE" connection on the router to
the corresponding DSL port on your DSL splitter using the supplied connection cable.
• Then, connect the network port („LAN") to a free port on a network switch (e.g. a network
switch with 5 or 8 ports, Gigabit or 10/100 Mbit) or with the network port on your computer.
• Connect the router to the mains voltage, using the supplied wall plug transformer, and then
turn on the router (the On/Off switch is located next to the low-voltage socket on the back of
the router). The router now performs a self test (LEDs blink). Wait until the self test is comple-
ted (approx. 30-60 seconds).
• Switch on your PC and wait until the operating system has fi nished loading.
Start-up and Confi guration
• The router works as a DHCP server and thus automatically assigns IP addresses to the con-
nected computer(s). The default IP address range is 192.168.1.x , whereby the router uses
the IP address 192.168.1.1; the subnet mask is 255.255.255.0.
• The router must be switched on fi rst, to ensure that the computer(s) receive(s) an IP address
from the router, and only after this can the computer(s) be switched on. Alternatively, you can
deactivate the appropriate network interface card, e.g. from the Windows control panel, and
then reactivate it after a few seconds. As a result, Windows gets a new IP address.
All manuals and user guides at all-guides.com
Confi guration using Software
www.conrad.com
☞
Version 07/11
• If you want to use the enclosed software for confi guration, fi rst place the CD in the correct
☞
• You can leave the software at any time by clicking on "Exit".
• First chose your provider from the choice menu. If your provider is not listed here, then click
• Now enter your access data (generally the user name and the password that belongs to it),
• Finally, click on "Setup". Now the confi guration is transferred to the router. Please note that
• Of course you can change the settings of the router's web interface at any time. For informa-
Manual Confi guration
• For the manual confi guration you can enter the IP address 192.168.1.1 into the address line
☞
• Now you can change the settings to what you prefer.
☞
Handling
We recommend that you use the enclosed confi guration software to confi gure the
router. Please note that to accomplish this, a version of Internet Explorer 7 or higher
must be installed on your computer.
drive of your computer. If the installation does not start automatically, begin the set-up pro-
gram manually (at the time that these operating instructions were written, the program was to
be found with the name "setup.exe" to be started from the root directory of the CD).
In some individual cases it might happen that the software is being blocked by the
antivirus software or your fi rewall. Before you can continue with the confi guration,
you must adjust the settings of your security software accordingly, or temporarily
disable them
In order to start the confi guration, click on "Easy Confi guration" from the menu. If the program
does not start, then start it manually (at the time these operating instructions were written, the
program "vbpES.exe" was to be started in the path"\fscommand\Easy_Setup\English\"of the
CD).
Click on the button "Web interface" to open the web interface of the router in the internet
browser.
on the option "Anderer DSL Provider".
that you have received from your provider.
Some suffi xes, such as, for example "@t-online.de" must only be entered if you have chosen
"Anderer DSL Provider".
this was returned to the default settings.
This process can take several minutes. When it is completed access to the internet is possible.
tion about this please see the next chapter.
of your internet browser (http://192.168.1.1). It may be necessary to change your fi rewall or
anti-virus software so that you can get access.
As an alternative, you can simply start the confi guration software and click on the
button „Web interface".
Then you need to enter your user name and the password for your router. The default setting
includes the user name "admin" and the password "1234". After this the router's confi guration
menu appears.
Please note that for the manual confi guration VPI (Virtual Path Identifi er) and VCI
(Virtual Channel Identifi er) values are to be entered. These values depend on the
provider you use. For most German internet providers, such as T-Online, the VPI va-
lue is "1" and the VCI value is "32". Exact details can be obtained from your provider.
Please do not forget to activate the "Bridge Interface" before you fi nish the confi gu-
ration, since without this it is not possible to dial into the DSL network.
Only to be used in dry, enclosed rooms. The product must not get damp or wet,
lethal danger of an electric shock!
Never use the product immediately after it has been taken from a cold room to a
warm one. The condensation that forms might destroy your unit.
Allow the device to reach room temperature before switching it on. This may take
several hours. Only then can the transformer be plugged into the mains and the
router put into operation.
Ensure that the insulation for the entire product is neither damaged nor destroyed.
The housing must not be opened! Any maintenance or repair work must only be
carried out by authorised personnel.
Check the product for damage before each use!
If you detect any damage, DO NOT connect the product to the mains supply! This
presents a danger to life!
It can be assumed that safe operation is no longer possible if
- the device is visibly damaged,
- the device does not operate any longer and
- the device has been stored under unfavourable conditions for a long period of time or
- it has been subjected to considerable stress during transportation.