Publicité
Les langues disponibles
Les langues disponibles
3. PREPARING THE INSTALLATION
3.1 Transport to installation site
and unpacking
The appliance is very heavy.
Take maximum care during handling
to avoid injury.
The appliance should always be
transported in an erect position.
Avoid at all costs leaning it on its front
side.
2
4
1
3
Since this is a large and heavy appliance, before trans-
porting the appliance, check the access to the loca-
tion where it will be installed (door size, maneuvering
space in stairwells, etc.).
The appliance is attached to the base of the packaging
(pallet) through four bolts which can be removed us-
ing a 19 mm (3/4") wrench.
It is recommended to use a manual transporting de-
vice to move the appliance to the installation site, and
only at this point to remove the base of the packaging.
The appliance should always be transported in an
erect position.
If this is not possible, transport the appliance laying
on its rear side.
Once at the installation site, the appliance, which is
equipped with four wheels, can be taken off the pallet
and positioned in the installation area.
Operate as follows:
> Take off the four bolts securing [ 1 ] the appliance to
the pallet by means of a 19 mm (3/4") wrench or socket.
> Remove the fixing brackets [ 3 ] and [ 4 ] .
> To release the front fixing bracket [ 3 ] , unscrew the
rear wheel adjusting bolt [ 2 ] by means of a 13 mm
(1/2") wrench or socket. Avoid straining this bolt at its
stop points one way or the other so as to not damage
the rear leveling system.
Ensure the front leveling legs are retracted so that all
4 wheels are able to contact the floor for easiest ma-
neuvering.
> From the back of the unit and by means of a suit-
able, high duty hand trolley, take off the appliance and
place it on the floor.
Be very careful to avoid any damage to floors. Delicate
floors should be protected with plywood, hard card-
board or similar material panels.
8
1
3.2 Electrical and water connection
The Built-in filter cannot make it safe to
drink any water which is not suitable for
human consumption.
The appliance should be connected only
to a potable water supply system.
Do not use extension cords or adapters.
Once the appliance is fully installed, con-
nected to the water supply (if applicable)
and operational, in the event that the wa-
ter supply must be turned off, (touch the
button
on control panel to disable the
Ice Maker
Water Filter
ice maker) before the main water is shut
Water System Purge
off to prevent the appliance from entering
a 'NO WATER IN' alarm state.
E
W
E
W
E
W
ELECTICAL & WATER
CONNECTION
W
E
The appliances are delivered from the factory for op-
eration at 110V-120V AC - 60Hz (US and Canada).
They are provided with a suitable supply cable and
plug to be connected to an appropriate 15A socket
providing an effective grounding.
A dedicated 15A circuit breaker should also be in-
stalled and should be easily accessible so that it can
be easily switched off before performing any installa-
tion or maintenance.
To connect to the water supply system (for appliances
equipped with ice makers) a 1/4" waterline with ac-
cessible shut-off valve must be supplied.
The appliance is provided with a water adapter elbow
which is suitable for the recommended water pres-
sure and complies the applicable food and water reg-
ulations.
The water filter cartridge, which is provided with the
appliance, should be installed according to the ac-
companying instructions. Please refer to water filter
installation instructions contained in the water filter
kit. The solenoid connection on the appliance is 3/4"
diameter but is metric threaded (NPT). A standard
E
W
E
W
E
W
W
E
W
E
W
E
Publicité
