ISC RT 350 Mode D'emploi page 15

Anleitung RT 350 SPK 7
the rotary knob (Figure 6 Item 1) and then adjusting
the telescopic tube. Then tighten the rotary knob
again.
8. To start
The grass trimmer is designed only to cut grass.
The grass trimmer has a semi-automatic line
extension system. Each time you activate the semi-
automatic line extension system, the line will be
extended to ensure that you can cut your lawn with
the perfect cutting width at all times.
Please note that the wear on the line will be
increased if you activate the semi-automatic line
extension system frequently.
Note
If the line is too long when you use the machine
for the first time, the surplus end of it will be cut
by the blade on the safety hood.
If the line is too short when you start the machine
for the first time, press the knob on the line spool
and pull the line hard. When you then start the
machine for the first time the line will be cut to
the perfect length automatically.
Your grass trimmer will work at its best if you
observe the following instructions:
Never use the grass trimmer without its safety
devices.
Do not cut grass when it is wet. The best results
are had on dry grass.
Connect the power cable to an extension cable
and hook the extension cable on the handle
(Figure 9).
To switch on your grass trimmer press the safety
lock-off (Figure 1 Item 4) and then press the
ON/OFF switch (Figure 1 Item 3).
To deactivate the grass trimmer, let go of the
On/Off switch (Figure 1 / Item 3).
Do not move the grass trimmer against the grass
until the switch is pressed, i.e. wait until the
trimmer is running.
For the correct cutting action, swing the grass
trimmer to the side as you walk forward, holding
it at an angle of approx. 30° as you do so (see
Figure 10 and Figure 11).
Make several passes to cut long grass shorter
step by step from the top (see Figure 12).
Make full use of the edge guide and the guide
hood in order to avoid unnecessary line wear
(see Figure 13 and Figure 14).
Keep the grass trimmer away from hard objects
in order to avoid unnecessary line wear.
9. Using the grass trimmer as an edge
cutter
The grass trimmer can be adapted in the following
way to cut the edges of lawns and flower beds:
Disconnect the grass trimmer from the power
supply!
17.10.2003 9:01 Uhr Seite 13
Push the button (Figure 11 Item 1) in the
direction indicated by the arrow and pull the
handle off the telescopic tube. Turn the handle
through 180° and slide it back into the telescopic
tube. The lever will engage automatically.
The grass trimmer has now been converted into
an edge cutter suitable for vertical cutting (Figure
12).
10. Replacing the line spool
Be sure to disconnect the power plug from the power
supply by you replace the line spool!
Press the sides of the spool cover as shown and
remove it with the spool (Figure 13 und Figure
14). Ensure that you do not lose the spring.
Remove the empty line spool.
Thread the ends of the line on the new line spool
through the eyelets in the spool cover.
Fit the spool cover and spool back into the spool
mounting.
When you start the machine again the line will be
cut to the perfect length automatically.
Caution! Catapulted pieces of nylon line may
cause injury!
11. Cleaning and maintenance
Switch off and unplug the grass trimmer before
putting it away or cleaning it.
Remove deposits from the guard hood with a
brush.
Clean the plastic body and plastic parts with a
mild household detergent and a damp cloth.
Never use aggressive agents or solvents for
cleaning purposes!
Never spray down the grass trimmer with water.
Prevent water getting into the trimmer at all cost.
12. Troubleshooting
The machine will not work: Check that the power
cable is connected properly and check the mains
fuses.
If the machine will not work despite the voltage
supply being OK, send it to the specified after-
sales service address.
13. Waste disposal
Important
The grass trimmer and its accessories are made
of various types of material, such as metal and
plastic. Defective components must be disposed
of as special waste. Ask your dealer or your local
council.
14. Ordering replacement parts
Please quote the following details when ordering
replacement parts:
Type of machine
Article number of the machine
Serial number of the machine
Replacement part number of the part you require
(Refer to the replacement parts list)
GB
13