Chicago Pneumatic CP7823 Guide D'utilisation page 4

EN
English
INSTRUCTION MANUAL
This product is designed for installing and removing
threaded fasteners in wood, metal and plastic. No
other use permitted. For professional use only.
Air Supply Requirements
1. Supply tool with 90 psig (6.2 bar) of clean, dry air.
Higher pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose, and
fitting sizes shown in the diagram.
3/8" (10mm)
3/8" (10mm)
Lubrication
1. Use an air line lubricator with SAE #10 oil,
adjusted to two (2) drops per minute. If an air line
lubricator cannot be used, add air motor oil to the
inlet once a day.
2. Monthly, lubricate the drive bushing and ratchet
yoke with a good grade bearing grease.
Periodically, depending upon use, the ratchet
head assembly should be removed, cleaned and
re-greased.
Maintenance
1. Tool should be oiled on a daily basis for best
performance. Every 3 to 6 months the tool's head
should be greased using approved CP Gear
Grease. If the tool loses performance over time,
tool should be sent to a CP Certified Service
Center to be checked and repaired as needed.
2. High wear parts are underlined in the parts list.
3. To keep downtime to a minimum, the following
service kits are recommended:
8940163005 Tune-Up Kit
(Incl: 5, 6, 7, 8, 15, 31, 32, 33, 37, 39)
8940163008 Ratchet Head Replacement Kit (CP7823)
(Incl: 30, 31, 32, 33, 34, 35, 36, 37, 38, 39)
8940164570 Ratchet Head Replacement Kit (CP7824)
(Incl: 30, 31, 32, 33, 34, 35, 36, 37, 38, 39)
8940163078 Ratchet Head Cover
8940163090 Specific Disassembly Tool
Copyright 2007, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks,
model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of
unauthorized parts is not covered by Warranty or Product Liability.
1/2" (12mm)
CA048362 (1/2")
3/8" (10mm)
90
0 130
3/8" (10mm)
3/8" (10mm)
CA048360 (1/2")
CA048361 (1/2")
EC DECLARATION OF CONFORMITY
We, Chicago Pneumatic Tool Co. LLC, 13325
Carowinds Blvd., Charlotte NC, 28273 USA, declare
under our sole responsibility that the product to which
this declaration relates, is in conformity with the
requirements of the Council Directive of June 1998 on
the approximation of the laws of the Member States
relating to machinery (98/37/EC).
Machine Name CP7823 & CP7824 Ratchet Wrench
Machine Type Assembly Power Tool for Threaded
Fasteners - No other use is permitted.
Serial No. Tools with No. 2006-330-K or higher
Technical Data
1/4" Sq. Dr. / 3/8" Sq. Dr.
Rated Speed 250 rpm
Air pressure 90 psi (6.2 bar)
Harmonized Standards Applied EN 792-6
National Standards Applied ISO 8662-1, ISO 15744-
2002
Name And Position Of Issuer Stéphane
Rakotoarivelo, General Manager
Signature Of Issuer
Date Of Issue November 1, 2007
Noise & Vibration Declaration*
Sound pressure level 85 dB(A) uncertainty 3 dB(A),
in accordance with ISO 15744-2002. For sound
power, add 11 dB(A).
Vibration value 5.5 m/s , re. ISO 8662-1.
* These declared values were obtained by laboratory
type testing in compliance with the stated standards
and are not adequate for use in risk assessments.
Values measured in individual work places may be
higher than the declared values. The actual exposure
values and risk of harm experienced by an individual
user are unique and depend upon the way the user
works, the workpiece and the workstation design, as
well as upon the exposure time and the physical
condition of the user. We, Chicago Pneumatic,
cannot be held liable for the consequences of using
the declared values, instead of values reflecting the
actual exposure, in an individual risk assessment in a
work place situation over which we have no control.
CP7823 & CP7824
Air Ratchet
2