Sauder Costa Serie Instructions D'installation

Masquer les pouces Voir aussi pour Costa Serie:

Instructions d'installation (52 pages)

page de 32

/ 32
Signets

Liens rapides

Télécharger ce manuel

sauder.com

Hutch

Costa Collection | Model 419961

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

For things 'n such.

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-22

Français pg 23-25

Español pg 26-28

Lot # 510843

11/20/17

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Sommaire des Matières pour Sauder Costa Serie

Page 1 Costa Collection | Model 419961 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
Page 2 No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identiﬁ cation Assembly Steps 5-22 Hammer Not actual size Français 23-25 Español 26-28 Nail holder (provided) Safety 29-30 Tape Measure Warranty Electric drill with 3/16" bit (ONLY in indicated step) Page 2 419961 www.sauder.com/services...
Page 3 Use this part identiﬁ cation to help identify similar parts. END (2) ADJUSTABLE SHELF (2) BRACE (1) FRONT LEG (2) ADJUSTABLE SHELF MOLDING (2) RIGHT REAR LEG (1) END MOLDING (2) BACK (1) K2 TOP (1) VALANCE (1) LEFT REAR LEG (1) www.sauder.com/services 419961 Page 3...
Page 4 Do not accidentally throw away. RUBBER SLEEVE - 8 NAIL - 12 CAM COVER - 16 METAL PIN - 8 BLACK 9/16" LARGE HEAD SCREW - 4 BLACK 9/16" FLAT HEAD SCREW - 4 Page 4 419961 www.sauder.com/services...
Page 5 Assemble your unit on a carpeted ﬂ oor or on the empty å carton to avoid scratching your unit or the ﬂ oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (12F) into the large holes in the ENDS (A) and VALANCE (D).
Page 6 Push twenty-four HIDDEN CAMS (1F) into the edges of the å ENDS (A), BRACE (I), and ADJUSTABLE SHELVES (E). Arrow (24 used) Arrow Arrow Arrow Hole Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 419961 www.sauder.com/services...
Page 7 Step 3 Turn twenty CAM SCREWS (8F) into the LEGS (B, H, and J) å and SHELF MOLDINGS (F). (20 used) Remember: Righty tighty. Lefty loosey. www.sauder.com/services 419961 Page 7...
Page 8 Shoulder These edges should be even. Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS. BLACK 9/16" FLAT HEAD SCREW Shoulder (4 used in this step) Page 8 419961 www.sauder.com/services...
Page 9 END (A). This END (A) will become the left END (A). S u r f a c i t h H I D D E N These surfaces Edge with should be even. TWIST-LOCK® FASTENERS www.sauder.com/services 419961 Page 9...
Page 10 Step 6 Fasten the left END (A) to the TOP (K2). Tighten two å TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK ® FASTENER Fasten the VALANCE (D) to the TOP (K2). Tighten two å 1. Insert the dowel end of the FASTENER into the hole of the TWIST-LOCK®...
Page 11 Push a WOOD DOWEL (15F) into the RIGHT REAR LEG (J). å Fasten the BRACE (I) to the RIGHT REAR LEG (J). Tighten å the HIDDEN CAM. NOTE: Be sure the WOOD DOWEL inserts into the edge å of the BRACE. www.sauder.com/services 419961 Page 11...
Page 12 Fasten the BRACE (I) to the LEFT REAR LEG (H). Tighten å the HIDDEN CAM. NOTE: Be sure the WOOD DOWEL inserts into the edge of å the BRACE. For support, place packing foam and magazines here. Page 12 419961 www.sauder.com/services...
Page 13 REAR LEG. The CAM SCREWS should be closer to this edge. Lower edge of REAR LEG View shown without the LEFT END for clarity. For support, place packing foam and magazines here. www.sauder.com/services 419961 Page 13...
Page 14 CLIPS should bite into the BRACES as you tighten the screws. Off set edge Nail Nail slot holder 2" Bead Bead Lower edge 2" Bead Lower edge (3 used) NAIL BLACK 9/16" LARGE HEAD SCREW (12 used in this step) (3 used in this step) Page 14 419961 www.sauder.com/services...
Page 15 Base and the 420040 Lateral File. Go to step 13 if your 419960 Library Base or the 420040 å Lateral File is assembled. Go to step 14 if your 419960 Library Base or the 420040 å Lateral File is not assembled. www.sauder.com/services 419961 Page 15...
Page 16 Drill through these two small holes. Drill through these two small holes. Drill through these two small holes. Drill through these two small holes. Page 16 419961 www.sauder.com/services...
Page 17 BACK EDGE OF TOP å templates only if your 419960 Library Base or the 420040 Lateral File is assembled. Cut out the two å templates along the dashed lines and go LEFT TEMPLATE RIGHT TEMPLATE to step 14. www.sauder.com/services 419961 Page 17...
Page 18 This page was intentionally left blank. Cette page a été intentionnellement laissée vierge. Esta página fue dejada en blanco intencionalmente. Page 18 419961 www.sauder.com/services...
Page 19 LEFT TEMPLATE Drill through these four LEFT TEMPLATE outside edge. circles farthest away from the outside edge. Drill through the two circles closest to the outside edge. RIGHT TEMPLATE RIGHT TEMPLATE www.sauder.com/services 419961 Page 19...
Page 20 And, you know, your Library Base or Lateral File. your arms. With the help of another person, carefully lift your HUTCH å and place it over the CAM SCREWS (8F). Tighten four HIDDEN CAMS. (4 used) Page 20 419961 www.sauder.com/services...
Page 21 5. Continue to turn until the screw starts spinning freely. NOTE: Before moving your unit to a diff erent location, unscrew the SAFETY DRYWALL ANCHOR (61M) from your wall. å The nylon sheath will remain behind your wall. www.sauder.com/services 419961 Page 21...
Page 22 This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. å And to celebrate, why not share your success story? No load 25 lbs. 25 lbs. (8 used) (16 used) To cover HIDDEN CAMS Page 22 419961 www.sauder.com/services...
Page 23 QUANTITÉ d’ a chat de cet élément et conserver le livret pour future référence. EXTRÉMITÉ ..............2 EXCENTRIQUE ESCAMOTABLE ....24 Pour contacter Sauder PIED AVANT..............2 VIS D'EXCENTRIQUE ..........24 en ce qui concerne cet MOULURE D’EXTRÉMITÉ ........2 12F FIXATION TWIST-LOCK® ........6 élément, faire référence au numéro de lot et...
Page 24 Fixer l'ENTRETOISE (I) au PIED ARRIÈRE DROIT (J). Serrer Pour commencer l'assemblage, enfoncer une FIXATION l’EXCENTRIQUE ESCAMOTABLE. TWIST-LOCK® SAUDER (12F) dans les gros trous des EXTRÉMITÉS (A) et LAMBREQUIN (D). REMARQUE : S’ a ssurer d’insérer la CHEVILLE EN BOIS dans le chant de l'ENTRETOISE.
Page 25 Faire tourner quatre VIS D'EXCENTRIQUE (8F) dans les trous du dessus de la Base de bibliothèque ou du Classeur Latéral. Avec l’ a ide d’une autre personne, soulever soigneusement le SURMEUBLE et le placer sur les VIS D'EXCENTRIQUE (8F). Serrer quatre EXCENTRIQUES ESCAMOTABLES. www.sauder.com/services 419961 Page 25...
Page 26 EXCÉNTRICO ESCONDIDO ......24 et conserver le livret pour future référence. PATA DELANTERA ............2 BIELA DE EXCÉNTRICO ........24 Pour contacter Sauder MOLDURA DE EXTREMO ........2 12F SUJETADOR TWIST-LOCK®........6 en ce qui concerne cet CORNISA ................1 15F PASADOR DE MADERA .........2 élément, faire référence...
Page 27 Fije la CORNISA (D) al PANEL SUPERIOR (K2). Apriete dos SUJETADORES TWIST-LOCK®. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (12F) dentro de los agujeros grandes de Cómo utilizar el SUJETADOR TWIST-LOCK® SAUDER los EXTREMOS (A) y de la CORNISA (D).
Page 28 Base de Biblioteca o el Archivero Lateral. instrucciones en cuanto a importante información de seguridad. Esto completa el ensamblaje. Limpie con su pulimento para muebles preferido o un paño húmedo. Seque con un paño. Page 28 419961 www.sauder.com/services...
Page 29 Les téléviseurs peuvent être un téléviseur. cet eff et. particulièrement lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 419961 Page 29...
Page 30 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 30 419961 www.sauder.com/services...
Page 31 à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
Page 32 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Ce manuel est également adapté pour:

Costa 419961