Télécharger
Partager
Imprimer la page
Sauder Shoal Creek 409714 Instructions D'assemblage
  1. Manuels
  2. Marques
  3. Sauder Manuels
  4. Ameublement d'intérieur
  5. Shoal Creek 409714
  6. Instructions d'assemblage
Sauder Shoal Creek 409714 Instructions D'assemblage

Sauder Shoal Creek 409714 Instructions D'assemblage

Masquer les pouces Voir aussi pour Shoal Creek 409714:

Publicité

Liens rapides

Télécharger ce manuel
sauder.com
4-Drawer Chest
Shoal Creek Collection | 409714
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 358575
01/23/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicité

loading

Manuels Connexes pour Sauder Shoal Creek 409714

Sommaire des Matières pour Sauder Shoal Creek 409714

  • Page 1 Shoal Creek Collection | 409714 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Page 2 LARGE RIGHT DRAWER SIDE (3) RIGHT FRONT LEG (1) D138 LARGE LEFT DRAWER SIDE (3) LEFT FRONT LEG (1) D174 DRAWER BACK (1) REAR LEG (2) D175 LARGE DRAWER BACK (3) DRAWER FRONT (1) D983 DRAWER BOTTOM (4) Page 2 409714 www.sauder.com/services...
  • Page 3 Now you know Part Identifi cation our ABCs. D174 D983 D132 D175 D983 D138 www.sauder.com/services 409714 Page 3...
  • Page 4 • If equipped with a drawer interlock system, do not defeat or remove it. Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over. This is a permanent label. Do not attempt to remove! 04/10 332296 Page 4 409714 www.sauder.com/services...
  • Page 5 BLACK 9/16" LARGE HEAD SCREW - 15 BLACK 9/16" FLAT HEAD SCREW - 4 GOLD 5/16" FLAT HEAD SCREW - 32 NAIL - 16 BLACK 1-7/8" FLAT HEAD SCREW - 1 BLACK 1-9/16" FLAT HEAD SCREW - 20 www.sauder.com/services 409714 Page 5...
  • Page 6 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (X) into the large holes in the ENDS (A and B).
  • Page 7 DRAWER BRACES (F2). Turn ten CAM SCREWS (Z2) into the FRONT å Do not tighten the HIDDEN CAMS in this step. LEGS (G and H) and DRAWER FRONTS (J2 and O2). Arrow Arrow (10 used) Hole (10 used) www.sauder.com/services 409714 Page 7...
  • Page 8 Fasten the REAR LEGS (I) to the ENDS (A and B). Use six å BLACK 2-1/4" FLAT HEAD SCREWS (MM). Remember: Righty tighty. Lefty loosey. BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Edge with TWIST-LOCK® FASTENERS Edge with TWIST-LOCK® FASTENERS Angled edge Page 8 409714 www.sauder.com/services...
  • Page 9 Shoulder Apply pressure with your hands These edges as you guide the MOLDINGS over should be even. the SCREWS and onto the ENDS. BLACK 9/16" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 409714 Page 9...
  • Page 10 Step 5 Fasten the FRONT LEGS (G and H) to the å ENDS (A and B). Tighten six HIDDEN CAMS. These surfaces should be even. These surfaces Angled edge should be even. Angled edge Page 10 409714 www.sauder.com/services...
  • Page 11 Insert four CABINET ACTUATORS (GG) into the holes å shown in the RIGHT END (A). This pin must insert into the location holes in the RIGHT END (A). www.sauder.com/services 409714 Page 11...
  • Page 12 Diagram 5. Remove the INTERLOCK TRACK assembly from Diagram 4 and fl ip it over before inserting the å INTERLOCK TRACK (JJ) with CABINET ACTUATORS (GG) into the groove in the RIGHT END (A). STOP Be sure the interloack track snaps into each cabinet actuator. Page 12 409714 www.sauder.com/services...
  • Page 13 RAILS. If the gap is larger than 1/16", the drawers could lock up and not open. If this happens, open two drawers at the same time to override the interlock system. Remove the drawers to re-adjust the INTERLOCK TRACK assembly. www.sauder.com/services 409714 Page 13...
  • Page 14 Step 9 Fasten the LEFT END (B) to the TOP (C). Tighten two å ® How to use the SAUDER TWIST-LOCK FASTENER TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. Fasten four METAL BRACKETS (AA) to the BACK (E). Use å...
  • Page 15 LEFT END. Finished edge r f a I S T w i t - L O ® r f a I S T w i t - L O ® Finished edge www.sauder.com/services 409714 Page 15...
  • Page 16 Use two BLACK 9/16" LARGE HEAD SCREWS (PP) through the BRACKETS on the BACK (E) and into the RIGHT END (A). BLACK 9/16" LARGE HEAD SCREW (8 used in this step) NAIL (16 used in this step) Page 16 409714 www.sauder.com/services...
  • Page 17 SCREWS (30S). Repeat this step for the other large drawers. Fasten the DRAWER BRACE (F2) to the LARGE The smaller drawer will use DRAWER FRONT (J2), DRAWER å SIDES (D10 and D11), and DRAWER BACK (D174). DRAWER FRONT (O2). Tighten one HIDDEN CAM. www.sauder.com/services 409714 Page 17...
  • Page 18 å (8 used in this step) through the slotted hole in the SLIDE. Screw head - turn CAM to line up the hole in the SLIDE with the hole in the DRAWER SIDE. Roller end D138 Page 18 409714 www.sauder.com/services...
  • Page 19 Repeat steps 13 and 14 for the other drawers. å Slot Screw head - turn CAM to line up the hole in the SLIDE with D132 the hole in the DRAWER SIDE. 40CC These tabs must insert into the slots. D138 Post D132 Seated www.sauder.com/services 409714 Page 19...
  • Page 20 Fasten two PULLS (FF) to the LARGE DRAWER FRONT (O2). å Use four SILVER 3/4" MACHINE SCREWS (OO). Repeat this step for the other large drawers. å BLACK 1-1/8" MACHINE SCREW (3 used for the KNOBS) SILVER 3/4" MACHINE SCREW (12 used for the PULLS) Page 20 409714 www.sauder.com/services...
  • Page 21 -Never open more than one drawer at a time. -If equipped with a drawer interlock system, do not 35 lbs. defeat or remove it. Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over. 35 lbs. www.sauder.com/services 409714 Page 21...
  • Page 22 #4. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. Page 22 409714 www.sauder.com/services...
  • Page 23 EXTRÉMITÉ DROITE ..........1 40CA ÉLÉMENT DROITE............4 pour future référence. 40CB ÉLÉMENT GAUCHE ..........4 EXTRÉMITÉ GAUCHE ..........1 Pour contacter Sauder 40CC TIROIR DROIT ..............4 en ce qui concerne cet DESSUS ................1 élément, faire référence 40CD TIROIR GAUCHE ............4 DESSOUS ................2...
  • Page 24 Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® extrémité du RAIL DE VERROUILLAGE (JJ). Placer le RAIL DE VERROUILLAGE SAUDER (X) dans les gros trous des EXTRÉMITÉS (A et B). Répéter cette comme l'indique le schéma. étape pour les DESSOUS (D).
  • Page 25 REMARQUE : La tête de vis dans l'EXCENTRIQUE doit être visible à travers le trou fendu dans la COULISSE. Ceci complète l'assemblage. Nettoyer à l’ a ide d’une encaustique pour meubles ou d’un chiff on humide. Essuyer. www.sauder.com/services 409714 Page 25...
  • Page 26 EXCÉNTRICO ESCONDIDO ......10 EXTREMO IZQUIERDO ............1 pour future référence. BIELA DE EXCÉNTRICO ........10 PANEL SUPERIOR ..............1 Pour contacter Sauder en ce qui concerne cet SOPORTE DE METAL ..........4 FONDO ...................2 élément, faire référence POMO ..................3 DORSO ....................
  • Page 27 Gráfi co 1. Mida 38 mm de un extremo del CARRIL DE UNIÓN (JJ). Coloque el CARRIL DE UNIÓN como se muestra. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (X) en los agujeros grandes de los EXTREMOS (A y B). Repita este paso SUJECIÓN DE ACTUADOR / CARRIL: para los FONDOS (D).
  • Page 28 NOTA: La cabeza de tornillo del EXCÉNTRICO debe ser visible a través del importante información de seguridad. agujero alargado de la CORREDERA. Esto completa el ensamblaje. Limpie con su pulimento para muebles preferido o un paño húmedo. Seque con un paño. Page 28 409714 www.sauder.com/services...
  • Page 29 • Ne pas pousser le mobilier, surtout sur la être très lourd. moquette. Se faire aider par une autre personne pour soulever l’élément et le mettre en place • Cette unité doit être placée contre un mur.. www.sauder.com/services 409714 Page 29...
  • Page 30 • No empuje la unidad, especialmente sobre ser muy pesado. un piso alfombrado. Pide la ayuda de otra persona para levantar la unidad y colocarla en lugar. • Esta unidad debe ser colocada contra una pared. Page 30 409714 www.sauder.com/services...
  • Page 31 GARANTIE LIMITÉE DE 5 ANS 1. Sauder Woodworking Co. (Sauder®) off re une couverture de garantie limitée à l’ a cheteur 4. La présente garantie ne s’ a pplique qu’ a ux défauts garantis qui se produisent pour initial du présent produit pendant une période de cinq ans à...
  • Page 32 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.