Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Installation
Instructions
■ Check with your local public works department
for plumbing codes. You must follow these guidelines
as you install the Water Filtration system.
■ Use the Water Filtration system on a potable, safe-to-drink,
home COLD water supply only. The filter cartridge
will not purify the water or make it safe to drink.
■ DO NOT use on a hot water supply. Cold water supply only
(40-100° F).
■ Install or store where it will not be exposed to temperatures
below freezing or exposed to any type of weather. Water
freezing in the system will damage it.
■ Your Water Filtration system will withstand up to 125 pounds
per square inch (psi) water pressure. If your house water
supply pressure is higher than 100 psi, install a pressure
reducing valve before installing the Water Filtration system.
REQUIRED TOOLS FOR INSTALLATION
■ Phillips screwdrivers
■ Pliers
■ Adjustable wrench
REQUIRED PARTS FOR INSTALLATION
•
3/8" Tubing (Pex or Plastic)
•
2-3/8" NPT Fittings
•
Teflon Tape
®
•
2-3/8" Nuts
•
2 Tube Inserts
•
Sump Wrench - UCWRNCH
This GX1S01R is Tested and
Certified by NSF international
against NSF/ANSI Standard 42
for materials and structural
C
US
integrity requirements and
COMPONENT
against CSA B483.1.
All manuals and user guides at all-guides.com
SAFETY PRECAUTIONS
49-50247-1
GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225
Water Filtration System
GX1S01R
WARNING:
Do not use with water that
is microbiologically unsafe or of unknown quality
without adequate disinfection before or after the system.
Systems certified for cyst reduction may be used
on disinfected water that may contain filterable cysts.
Discard all unused and packaging material after installation.
Small parts remaining after installation could be a choke hazard.
OPTIONAL KITS AND TOOLS FOR INSTALLATION
NOTE: Sump wrench (UCWRNCH) and faucet (UNFCTBL)
are sold separately for model GX1S01R.
■ Drill and 1/4" bit (saddle valve installation)
■ Drill and drill bit for 3/4" hole (type as required)
if mounting hole is needed for faucet
■ Pipe cutter
■ File
CAUTION:
To avoid damaging the sink, consult a
qualified plumber or installer for drilling procedures. Special
drill bits may be needed for porcelain or stainless steel.
JR 10-08
1
Publicité
Manuels Connexes pour GE GX1S01R
Sommaire des Matières pour GE GX1S01R
- Page 1 REQUIRED TOOLS FOR INSTALLATION OPTIONAL KITS AND TOOLS FOR INSTALLATION ■ Phillips screwdrivers NOTE: Sump wrench (UCWRNCH) and faucet (UNFCTBL) are sold separately for model GX1S01R. ■ Pliers ■ Drill and 1/4″ bit (saddle valve installation) ■ Adjustable wrench ■ Drill and drill bit for 3/4″ hole (type as required)
- Page 2 5. Allow cold water to run until air is removed from water. NOTE: Sump wrench (UCWRNCH) and faucet (UNFCTBL) ″ are sold separately for model GX1S01R. Mounting bracket to wall Outlet The bracket can be used as a template for marking...
- Page 3 All manuals and user guides at all-guides.com FLUSH PROCEDURE Whenever water of unknown quality is passed through The procedure for flushing the GE Water Filtration system is: the GE Water Filtration system, filter elements should See Filter Cartridge Installation or Replacement section be discarded and the filtration system flushed.
- Page 4 GE. the cost of shipping or service to your home or office. — Liability on the part of GE under this or any other warranty Some states do not allow the exclusion or limitation of incidental for any indirect or consequential damage.
- Page 5 OUTILLAGE NÉCESSAIRE POUR L’INSTALLATION PIÈCES ET OUTILS OPTIONNELS POUR L’INSTALLATION ■ Tournevis Phillips NOTE : Les produits suivants sont vendus séparément pour le modèle GX1S01R : clé pour corps de filtre (UCWRNCH) ■ Pince et robinet (UNFCTBL). ■ Clé réglable ■...
- Page 6 Tube 5. Laisser couler l’eau froide jusqu’à ce que l’air soit éliminé de l’eau. NOTE : Pour le modèle GX1S01R, la clé pour corps de filtre (UCWRNCH) et le robinet (UNFCTBL) sont vendus séparément. Sortie d’eau...
- Page 7 All manuals and user guides at all-guides.com MÉTHODE DE PURGE Chaque fois que le système de filtration GE est exposé à de l’eau Méthode de rinçage du système de filtration GE : de qualité inconnue, on devrait jeter les éléments de filtration Voir la section Cartouche de filtration –...
- Page 8 à votre domicile ou votre bureau. non imputable à GE. Certains états n’acceptent pas d’exclusion ou de limites aux — Responsabilité de GE couvert par cette garantie ou toute autre dommages indirects consécutifs. Cette garantie vous donne des garantie couvrant tout dommage indirect.
- Page 9 PARA LA INSTALACION PARA LA INSTALACION ■ Destornilladores Phillips NOTA: Llave inglesa (UCWRNCH) y llave de agua (UNFCTBL) se venden separadamente para el modelo GX1S01R. ■ Alicates ■ Taladro punta de 1/4″ (instalación de válvula ■ Llave ajustable tipo montura) PIEZAS REQUERIDAS PARA LA INSTALACION ■...
- Page 10 NOTA: Llave inglesa para receptáculos (UCWRNCH) y ″ llave de agua (UNFCTBL) son vendidas separadamente para el modelo GX1S01R. Salida Instalacion de la abrazadera a la pared del gabinete Abrazadera La abrazadera puede ser usada como modelo para de montaje marcar la ubicación de los tornillos de montaje.
- Page 11 PROCEDIMIENTO DE LAVADO Cada vez que agua de calidad desconocida pasa a través El procedimiento para lavar el sistema de Filtración de Agua GE es: del sistema de Filtración de Agua GE, el elemento del filtro debería Vea la sección Instalación y Reemplazo del Cartucho del Filtro ser deshechado y el sistema de filtración lavado.
- Page 12 GE. doméstico dentro Estados Unidos. Si el producto está situado — Responsabilidad de parte de GE bajo esta o cualquier otra garantía en un área que no dispone de servicio por parte de un proveedor por cualquier daño indirecto o por consecuencia de otro evento.