Publicité
Les langues disponibles
Les langues disponibles
CHARACTERISTICS
ES
▶Power: 1,000/2,000W
▶2 levels
FUNCTIONING
PT
▶Before connecting the device to the network, make sure that the
switch is in the "0" position.
▶Plug the power cord into the AC 220-240V~ 50Hz outlet.
EN
▶Through the 2 power system you can start the appliance.
• POSITION 0: OFF position, no button pressed.
• FRESH AIR POSITION: air fan
FR
• POSITION 1: first speed -1,000W
• POSITION 2: second speed - 2,000W
▶If you do not use the appliance for a long time, unplug the power
cord from the electrical outlet.
▶Never try to disassemble the device.
▶If you notice any abnormality (such as unusual noise from the
device), turn off the device and unplug it immediately.
▶Do not use this heater with a programmer, timer or other device that
switches the heater on automatically, as there is a risk of fire if the
heater is covered or positioned incorrectly
▶Make sure that no objects or liquids get inside the appliance through
the openings.
▶The device must only be used in dry environments. Do not use in the
immediate vicinity of a bathtub, shower or swimming pool
▶Protect the device from dust, moisture, sunlight, and direct heat.
CONTROL PANEL
▶Press
as follows: low heat, low heat + swing, high heat, high
heat+swing, fan.
over 3sec: then can set timer as follows: 1h, 2h, 3h,...8h.
▶Press
REMOTE CONTROL
ON/OFF
▶The appliance will turn on and fresh air will come out by default. If
you press it again, the device turns off.
OPEN WINDOW DETECTION
• 1. Open window detection can only be started when the appliance
is in heating mode (cannot be turned on when operating as fan) or
set temperature mode.
Instruction manual
Observations
▶Press
▶You can also press
▶Press as follows: low temperature, high temperature, fan working.
▶Presione de la siguiente manera: Swing ON, Swing OFF.
▶Press to set the timer as follows: 1h, 2h, 3h, ..., 8h. When the weekly
▶Press
▶The fan continues to run for 30 seconds when you turn off the
Note: the indicator lights up when the corresponding functions are
working
▶1. Press and set to standby temperature mode, press "+" "-" to
▶2. Press OK, or after flashing LED 5s, it will start setting temperature
▶The first time to start (start after power off), it is necessary to set
• 2. Press
, to enable open window detection, or turn off
detection
• This function is used for when the heater notices a sudden drop in
temperature - associates that it may be caused by an open window
in the room where the cold air from outside enters and causes the
temperature to drop drastically - to avoid wasting electricity, the
heater It has an automatic stop working.
to restart to the same working mode before the
appliance stopped.
to turn off, and then it will restart with
room temperature to re-program which mode and temperature you
want.
HEATING
OSCILLATION
TIMER
timer starts, you cannot set this timer function.
or
about 3s, then you can set the temperature.
Temperature range 18-45ºC, press
45ºC, press
to adjust the temperature to 18ºC.
appliance (only after warming up).
SET TEMPERATURE
adjust temperature.
• The temperature range is 18-45ºC.
• Press "-": the set temperature is equal to or lower than room
temperature, please stop heating.
• Press "+": the set temperature is 1-2 "C higher than room
temperature, under heating.
• The set temperature is greater than or equal to room temperature
+ 3ºC, high heating.
mode.
WEEK TIMER
the current time.
Ref. 07206
to set the temperature up to
Publicité
