Amica UM100.3 Notice D'utilisation page 68

DOOR REVERSAL
The door of the refrigerator can be opened both from the left or right as required. The following are the steps
required to position the door to open to the right.
Remove the lower bracket (1) on the right, the door and the screw hole cover (4). Remove the lower bracket
pivot (3) and the spring washer (2), and then place and fix them in the hole on the left of the lower bracket.
Remove the cover (5) on the upper brackets on both left and right sides; remove the bracket pivot on the
right side and the spring washer and then fix them in the bracket hole. Install the door between the upper and
lower brackets on the left and fasten the lower bracket by tightening the screws. Install the screw hole cover
in the lower bracket hole on the right, and then install the upper bracket covers on the upper brackets on the
left and right. After installation open and close the door to ensure the door operates correctly. Move the com-
ponents (7) and (8) with the special tool provided. Remove the screw (9) from the refrigerator, open the door
fully and replace screw (9) in the corresponding opposite position. Remove and replace component (10), at
the corresponding position on the left, with the special tool provided. Fix component (7) in the corresponding
opposite position.
VENTILATION
Level the kitchen cabinet unit with a spirit level and a try square. Level the unit by placing packing material under-
neath if required. A minimum gap of 38mm must be maintained at the back of the appliance for ventilation. Air inlet
A must be at least 200 cm square and air must flow through the panel in the cabinet plinth. Check that the position
of the power socket (1) is correct. Mains voltage where the appliance is to be used must comply with that shown on
the data plate located on the left inside wall of the appliance next to the vegetable bins. The power supply must be
suitably earthed.
INSTALLATION OF THE APPLIANCE
Installation of the appliance should be performed by a qualified installer. The appliance should be placed in furniture
case. Run the mains cable through the unit such that it can be connected to the power supply after installing the
appliance. Remove the cover (6) only if space is restricted. Place the refrigerator into the kitchen unit. Fix the
brackets (1) with screws (2) onto the upper frame when two third of the refrigerator has been inserted. Then insert
the refrigerator in completely, ensuring that the gib clamp of the brackets stuck on the horizontal frame of the kitchen
unit. Adjust the position of the refrigerator making a 6mm space between inside wall of the kitchen unit and external
sides of the refrigerators. Fix the brackets to the horizontal frame of the kitchen unit with screws. Insert the seal in
the aperture (approx. 10mm) between the lower front frame and bottom board of the kitchen. Fix lower brackets (3)
to the lower front frame with screws (2). Fix the lower brackets to the bottom board of the kitchen unit with screws
(2). Properly insert seals in the apertures on the left, upper and right sides of the refrigerator.
FITTING FURNITURE BOARD TO APPLIANCE DOOR
Parts List:
1. Fridge Door x 1
2. Wooden Door x 1
3. Right Frame x 1
4. Left Frame x 1
5. Top Frame x 1
6. Bottom Frame x 1
7. Self-Tapping Screws (ST3.9x16) x 10
Installation Steps:
Fit the bottom frame (5) on the bottom edge of fridge door (1) with 3 screws (7). Screws should not be too tight so
that the bottom frame could be adjusted if necessary. Fit the left (4) and right (3) frames on to the sides of fridge
door (1) with 4 screws (7). Screws should not be too tight so that the frames could be adjusted if necessary. Put
the wooden door (2) into the gap of the frames along the direction of the arrow, adjust the frames (3\4\5) to ensure
the frames could hold the wooden door (2) properly. Fit the top frame (6) on the top edge of the fridge door (1)
with 3 screws (7). Adjust the four frames (3/4/5/6) to fit properly and tighten the screws (7).
68
EN