Publicité
Liens rapides
7300 PT, PTH
Tool List
Tape Measure
Center Punch/Hammer
3/16" Slotted Screw Driver
#3 Cross-Point Screw Driver
1/2" Wrench
7/16" Box Wrench
7/32" Drill Bit / Drill
1/4-20 Tap / Tap Holder
3/8" & 5/32" Drill Bit
2.5mm & 5mm & 6mm
Hex Wrench
Components/Componentes/Pièces
Door Closer
1
Cierrapuertas
Ferme-porte
Arm
2
Asidero de Plunger Abre Brazo
Prise de Plunger Ouvre le Bras
Dust Cap
3
Guarda polvos
Capuchon anti-poussière
Track
4
Riel
du rail
End Block
5
Tope Final
Bloc d'extrémité
Slide Shoe
6
Zoclo Deslizante
Sabot de glissière
www.dorma-usa.com
All manuals and user guides at all-guides.com
Lista de Herramientas
Cinta métrica
Perforadora Central/Martillo
3/16" desarmador plano
Desarmador de Cruz del #3
Llave Inglesa de ½"
Llave Inglesa de Caja de 7/16"
Broca / Taladro del 7/32"
Canilla / Sostenedor de Canilla de ¼-20
Broca de 3/8" & 5/32"
Llave Inglesa Hex de
2.5mm & 5mm & 6mm
Rubber Stop
7
Tope de goma
Butoir de caoutchouc
Flat Head Combo Screws
8
Tornillos de Cabeza Plana Combo
Vis combo à tête plate
Pinion Screw
9
Tornillos de Piñón
Vis Pignon
Slide Shoe Screw
10
Tornillos Zoclo Deslizante
Vis Sabot de glissière
1-800-523-8483
Liste des outils
Ruban à mesurer
Pointeau / Marteau
Tournevis à fente 3/16"
Tourne-vis à pointes croisées #3
Clé 1/2"
Clé polygonale 7/16"
Clé à molettes 10"
Perceuse / Mèche 7/32"
Taraud 1/4-20
Mèches 3/8" & 5/32"
Clé hexagonale
2.5mm & 5mm & 6mm
Optional Components
Componentes Opcionales
Pièces facultatives
11
Cover
Cubierta
Boîtier
12
Hold Open Mechanism
MECANISMO DE RETENCIÓN
Mécanisme de retenue (HO)
13
Plates
Placa
Plaques
(BP86T & BP86TFC)
INSPK NO. 08280510 Rev.12/08
08280511
PAGE
INS NO.
1 of 5
12/08
Rev.
Publicité
Manuels Connexes pour dorma 7300 PT
Sommaire des Matières pour dorma 7300 PT
- Page 1 All manuals and user guides at all-guides.com 7300 PT, PTH Tool List Lista de Herramientas Liste des outils Tape Measure Cinta métrica Ruban à mesurer Center Punch/Hammer Perforadora Central/Martillo Pointeau / Marteau 3/16" Slotted Screw Driver 3/16" desarmador plano Tournevis à fente 3/16"...
- Page 2 All manuals and user guides at all-guides.com PUSH TRACK / RIEL DEL LADO DE EMPUJE / RAIL à POUSSER (LH) (LH) Prepare door and frame using template. Prepare puerta y plantilla de usar de marco. Préparer la porte et le cadre à l'aide du gabarit. (LH) (RH) For hold open units, see page 3.
- Page 3 All manuals and user guides at all-guides.com HOLD OPEN UNITS ONLY, UNIDADES CON RETENCIóN úNICAMENTE, MODÈLE A CRAN D'ARRÈT SEULEMENT NOTE: HOLD OPEN MECHANISM AND SLIDE SHOE MUST BE INSTALLED WITH ARROWS POINTING AWAY FROM THE DOOR HINGES. (ARROWS ARE STAMPED ON SLIDE SHOE & HOLD OPEN MECHANISM) NOTA: EL MECANISMO DE RETENCIÓN Y EL ZOCLO DESLIZANTE DEBEN SER INSTALADOS CON LAS FLECHAS APUNTANDO HACIA FUERA DE LAS BISAGRAS DE LA PUERTA.
- Page 4 All manuals and user guides at all-guides.com Technical Notes: CAUTION: Sex nuts are required for attachment of components to unreinforced, wood or plastic faced composite type fire doors, unless an alternative method is identified in the individual door manufacturer's listings Make sure door efficiently operates prior to installing closer.
- Page 5 All manuals and user guides at all-guides.com DO NOT REMOVE VALVES NO REMUEVA LAS VALVULAS. NE PAS RETIRER LES SOUPAPES 08280511 5 of 5 12/08 INS NO. PAGE Rev.