Publicité
Les langues disponibles
Les langues disponibles
N80CB TOOL SPECIFICATIONS
All screws and nuts are metric.
M M O O D D E E L L
T T O O O O L L A A C C T T U U A A T T I I O O N N
N80CB-1
Contact Trip
N80CB-2
Sequential Trip
N80CB-HQ
Contact Trip
FASTENER SPECIFICATIONS:
The N80CB tools uses wire collated coil nails in lengths of 1-1/2" to 3-1/4" (38.1 - 82.6mm) with shank
diameters of .099" - .131" (2.5 - 3.3mm)
The N80CB-HQ tools uses the same nails as the N80CB, but is optimized to accept wire collated 2-1/2"
(63.5mm) Hurriquake
®
nails with shank diameters of .113" and .131" (2.9mm and 3.3mm)
TOOL AIR FITTING:
This tool uses a 1/4 N.P.T. male plug. The inside diameter should be .275" (7mm) or larger. The fitting must be
capable of discharging tool air pressure when disconnected from the air supply. The connector socket on the
air hose should be .275" (7mm) inside diameter or larger.
OPERATING PRESSURE:
70 to 100 p.s.i.g. (4.9 to 7.0 kg/cm
performance. DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
AIR CONSUMPTION:
The N80CB requires 7.8 cubic feet per minute of free air to operate at the rate of 100 nails per minute, at 80
p.s.i.g. (5.6 kg/cm
2
). Take the actual rate at which the tool will be run to determine the amount of air required.
For instance, if your fastener usage averages 50 nails per minute, you need 50% of the 7.8 c.f.m. which is
required for running at 100 nails per minute.
OPERATION
BOSTITCH OFFERS TWO TYPES OF OPERATION FOR THIS SERIES TOOL
CONTACT TRIP:
The common operating procedure on "Contact Trip" tools is for the operator to contact the work to actuate the
trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted. This
will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly.
All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and
if unintentionally allowed to recontact the work surface with the trigger still actuated (finger still holding trigger
pulled) an unwanted second fastener will be driven.
SEQUENTIAL TRIP:
The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This makes
accurate fastener placement easier, for instance on framing, toe nailing and crating applications.
The Sequential Trip allows exact fastener location without the possibility of driving a second fastener on recoil,
as described under "Contact Trip".
The Sequential Trip Tool has a positive safety advantage because it will not accidentally drive a fastener if the
tool is contacted against the work – or anything else – while the operator is holding the trigger pulled.
MODEL IDENTIFICATION:
Refer to Operation Instructions on page 7 before proceeding to use this tool.
CONTACT TRIP
Identified by:
BLACK TRIGGER
All manuals and user guides at all-guides.com
L L E E N N G G T T H H
12-1/16" (306mm)
13-1/4" (336mm)
12-1/16" (306mm)
13-1/4" (336mm)
12-1/16" (306mm)
13-1/4" (336mm)
2
). Select the operating pressure within this range for best fastener
SEQUENTIAL TRIP
Identified by:
GRAY TRIGGER
-4-
H H E E I I G G H H T T
W W I I D D T T H H
5-9/16" (140mm)
5-9/16" (140mm)
5-9/16" (140mm)
W W E E I I G G H H T T
8 lb. 8 oz. (3.86kgs.)
8 lb. 8 oz. (3.86kgs.)
8 lb. 8 oz. (3.86kgs.)
Publicité
