BorMann BEW5100 Mode D'emploi page 3

Impact wrench safety instructions
a) Use the wrench correctly. Only use the impact wrench in the manner and for the functions described in this manual.
b) Check for misalignment or poor fastening of moving parts, damage to parts and any other condition that may affect the operation of the tool. If damaged,
have the tool serviced before use.
c) Use only accessories recommended by the manufacturer for your model. Accessories that are not suitable for your tool may cause injury or damages.
d) Choose the right sockets according to the size of the bolt and nut and for the size of the square drive. Use of wrong sockets will result in damages the bolt
and tool. The specification of bolt, nut and required torque must accord with the precision class of the bolt, nut and national standard. Use only impact wrench
sockets. Do not use standard sockets.
e) Do not force tool. When tightening a nut or bolt, never allow the wrench to impact more than 7-8 times to avoid over tightening. Finsh tightening the wheel
nuts with a torque wrench or suitable spanner to the wheel nut torque recommended by the tool manufacturer.
f) Carefully maintain the tool's power cable. Keep the cable well away from the machine and make sure you are working close to an electrical supply, so that
the operation is not restricted by the length of the cable. If working outdoors, always use an approved cable extension suitable for the power rating of this tool.
g) When using a cable reel, always unwind the cable completely.
h) Do not use tool if the switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
i) Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce
the risk of starting the tool accidentally.
j) Store idle tools out of reach of children and other untrained persons. Tools can be dangerous in the hands of untrained users.
k) Maintain tools with care. Keep tools in a good condition and make sure they are clean. Properly maintained tools are less likely to malfunction and are easier
to control.
NOTE: Torque and speed may vary depending on the operating time. When you want to assemble or disassemble a bolt, you want keep the tool running for
more than 5 seconds. Keeping the tool running for more than 5 seconds, does not equal higher torque. The torque will also vary according to different size of
bolt. Not using the appropriate sockets according to the size of the bolt and nut will also impact torque and speed.
SPECIFICATIONS
Technical Data
Model BEW5100
Voltage 230V/50hz
Power 450W
No-load speed 3600r/min
Torque 350Nm reverse, 100Nm forward
Shaft 1/2"
Cable Length 2m
Includes sockets 17 / 19 / 21 / 22mm
* The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the
products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer's product line with similar features and may not be included
in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall
not be liable for injuries and damages resulting from the use of non-conforming equipment.
Description
1. ON/OFF switch
2. 1/2" square drive (13mm)
3. Direction of rotation switch
4. Handle
5. Carbon brush replacement
Size of Bolt - Torque
M10-M12: 40-80 Nm
M12-M14: 100-200 Nm
M14-M18: 120-200 Nm
M18-M24: 200-320 Nm
WWW.NIKOLAOUTOOLS.GR
EN
3