HOMCOM C10-006V01 Manuel D'instructions page 3

WARNINGS
FITTING
01.Check with the assembly instructions that all the necessary parts are present.
02.Clean the car roof and those parts of the product that come into contact with the roof before and regularly
during use.
03.Go through and carefully follow the assembly instructions and the recom mendation list if one is included.
Then fit the unit in the correct sequence, that is to say 1,2, 3 and so on.
04. If no special fitting positions are given in the assembly instructions, try to maintain a minimum distance of
700 mm between the load carrier bars.
05.When carrying long loads, the distance between the load carrier bars should not be less than 600 mm.
06.Every time the unit is fitted, check that the load carrier is sitting securely on the roof. Try to push and pull
the carrier out of its locked position. Try also to pull out the tensioning tabs from the roof edge. f you manage
to move any part of the unit, the load carrier must be secured more firmly. This test should be carried out
regularly.
07.Some types of sunroof and radio antenna cannot be used when the carrier is fitted.
08.The roof rack is permitted to be assembled on cars with glass roof,unless otherwise is specified in mount-
ing instruction.
09.The manufacturer can not be held responsible for personal damages of property or lost of fortune caused
by incorrect mounting or use of the product.
10.No modifications to the product are permitted.
11.Consult with your dealer if you have any questions regarding the operations and limits of the products.
Review all instructions and warranty information carefully.
LOADING
01.The maximum load specified in the assembly instructions is not to be exceeded. However, this limit is
always subordinate to the maximum load recommended by the manufacturer of the car itself. It is always the
lower maximum recommended load that applies. Max. roof load= load carrier weight + any fitted carrier
accessories + the weight of the load itself.
02.The load may not significantly exceed the load carrier's width, and it should always be spread evenly
across the load carrier and with the lowest possible centre of gravity.
03. Maximum load applies to driving as well as parked vehicle.
04.When several surfboards are being carried, they should not be placed beside each other but instead one
on top of the other.
05.When carrying surfboards and other long items, these shall be secured both at the front and the rear of
the vehicle.
06.Skis must be carried with their pointed ends facing the rear of the vehicle.
07.All lose or removable parts of the load such as bike child seats, tyrepumps, fins and so on should be
taken off prior to loading.
08.The load should be thoroughly secured. Elastic bungees are not to be used.
09.The load's security should be checked after a short distance, and there after at suitable intervals. Tighten
the load's securing straps whenever necessary.
NOTE! Always check the load's attachment security.
DRIVING PROPERTIES AND REGULATIONS
01.Road speed should always be adjusted to suit the loadbeing carried and the current driving condtions,
such as road type andquality, wind conditions, traffic intensity and applicable speed limits.
02.The vehicle's speed must always be adjusted to the load being carried and the current driving conditions,
such as the roadtype, road quality, wind conditions, traffic intensity and applicable speed
limits, but must under no circumstances exceed 130 km/h.Applicable speed limits and other trafficregulations
must always be observed.
03. Drive slowly over speed bumps, maximum speed 10 km/h.
04.Note that the vehicle's total height increases when upright loads are carried.
05.The vehicle's driving characteristics and braking behaviour change and its vulnerability to side-winds
increases when a load iscarried on the roof.
06.Products fitted with a lock should always be locked during transport.
07.Off-road driving is only approved for roof rack without load or accessories attached.
08.Adapt your speed to the conditions of the road and load being carried, check tension of load carrierfre-
quently, especially when travelling on rough roads.
MAINTENANCE
01.Check and replace worn-out or defective parts.
02.The load carrier should always be cleaned and maintained, especially in the winter.
03. Screws, nuts and locks (if fitted) should be lubricated at regular intervals.
04. When not in use, the product should be removed from the vehicle.
05. When the product is removed from the vehicle, all loose parts should be stored safely.
-3-