Publicité
Les langues disponibles
Les langues disponibles
PULLEY SYSTEM FLOOR LAMP
Save these instructions
IMPORTANT SAFETY INSTRUCTIONS:
•
These instructions are provided for your safety.
Please read carefully and completely before beginning
the assembly and installation of this lighting fixture.
•
This lighting fixture is intended for indoor use only.
•
Always place lighting fixture on a solid, level surface.
To avoid the risk of fire, do not exceed the maximum wattage of 100W TYPE A lamp
•
or 23W Self-Ballasted lamp
(Bulbs not included)
•
This lighting fixture has a polarized plug (one prong is wider than the other) as a safety
feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one
way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. Never use with an extension cord unless plug can be fully inserted.
Do not alter the plug. Do not attempt to bypass this safety feature.
WARNINGS:
•
To reduce the risk of fire, electrical shock, or personal injury: always turn off and unplug this
lighting fixture and allow it to cool before attempting to replace the light bulb.
•
Do not touch light bulb while fixture is turned on.
•
Keep flammable materials away from this lighting fixture.
•
Never look directly at a lit bulb.
•
To avoid the risk of electric shock or damage, only use the supplied, pre-installed nylon set
screw to secure the position of the electrical cord as described in these instructions.
Never use a metal or pointed screw.
CARE INSTRUCTIONS:
•
Unplug lamp before cleaning.
•
Wipe clean with a soft, dry cloth or static duster.
•
Always avoid the use of harsh chemicals or abrasive cleaners as they may
cause damage to the fixture's finish
Made in China
, or 9W SB LED
lamp or lamp adapter.
Page 1 of 7
FL0022 FL0123 FL0124 rev032819EFS
,
Publicité
Table des Matières
Manuels Connexes pour Henn&Hart FL0022
Sommaire des Matières pour Henn&Hart FL0022
- Page 1 Do not alter the plug. Do not attempt to bypass this safety feature. WARNINGS: • To reduce the risk of fire, electrical shock, or personal injury: always turn off and unplug this lighting fixture and allow it to cool before attempting to replace the light bulb. • Do not touch light bulb while fixture is turned on. • Keep flammable materials away from this lighting fixture. • Never look directly at a lit bulb. • To avoid the risk of electric shock or damage, only use the supplied, pre-installed nylon set screw to secure the position of the electrical cord as described in these instructions. Never use a metal or pointed screw. CARE INSTRUCTIONS: • Unplug lamp before cleaning. • Wipe clean with a soft, dry cloth or static duster. • Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the fixture’s finish Made in China Page 1 of 7 FL0022 FL0123 FL0124 rev032819EFS...
- Page 2 ADJUSTABLE OPTIONS: OPTIONS AJUSTABLES : OPCIONES AJUSTABLES: Page 2 of 7...
- Page 3 PRE-ASSEMBLY: Carefully remove all parts and hardware from carton, along with any protective plastic packaging. Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware. PARTS: (A) Base (B) Bottom Support Post (C) Center Support Post (D) Top Support Post (E) Washer (F) Thumb Screw (G) On/Off Switch (H) Cord/Socket (I) Shade NOTE: Use screwdriver (J) Shade Ring with the preinstalled set (K) Light Bulb (not included) screw to adjust and secure the (L) Screwdriver cord for lamp shade position.
-
Page 4: Lampadaire De Système De Poulie
LAMPADAIRE DE SYSTÈME DE POULIE Conservez ces instructions CONSIGNES DE SÉCURITÉ ESSENTIELLES : • Ces consignes sont fournies aux fins de votre sécurité. Veuillez les lire attentivement et au complet avant de commencer l’assemblage et la mise en place de ce luminaire. • Ce luminaire est destiné à utilisation à l’intérieur seulement. • Posez toujours ce luminaire sur une surface solide et de niveau. • Pour éliminer tout risque d’incendie, évitez de dépasser la puissance maximale prescrite d’une ampoule TYPE A de 100 W , ou d’une ampoule à lumière mixte de 23 W , ou d’une ampoule à... -
Page 5: Préassemblage
PRÉASSEMBLAGE : Retirez soigneusement de la boîte toutes les pièces, toute la quincaillerie, et tout emballage de plastique protecteur. Ne mettez aucun élément de contenu au rebut avant de terminer l’assemblage au complet, afin d’éviter de jeter accidentellement de petites pièces ou un élément de quincaillerie. PIÈCES : (A) Base (B) Barre de support inférieure (C) Barre de support centrale (D) Barre de support supérieure (E) Rondelle (F) Vis à oreilles (G) Bouton ON / OFF (H) Cordon électrique / prise REMARQUE : (I) Abat-jour... -
Page 6: Instrucciones Importantes De Seguridad
LÁMPARA DE PIE DEL SISTEMA DE LA POLEA Guarde estas instrucciones INSTRUCCIONES IMPORTANTES DE SEGURIDAD: • Estas instrucciones se proporcionan para su seguridad. Léalas cuidadosamente y por completo antes de comenzar a ensamblar e instalar esta lámpara. • Esta lámpara está destinada a ser utilizada solo en interiores. • Coloque siempre la lámpara sobre una base firme y nivelada. Para evitar el riesgo de incendios, no exceda el vataje máximo de una bombilla de • 100W TIPO A , de 23W con balasto incorporado , LED SB de 9W , o un adaptador para bombilla. (No se incluyen las bombillas) •... - Page 7 ANTES DEL ENSAMBLADO: Retire con cuidado todas las piezas y herramientas de la caja, junto con todo el envoltorio plástico protector. No deseche nada hasta después de haber terminado de ensamblar para evitar botar por accidente piezas pequeñas o herramientas. PARTES: (A) Base (B) Barra de soporte inferior (C) Barra de soporte central (D) Barra de soporte superior (E) Arandela (F) Tornillo de pulgar (G) Interruptor encendido / apagado (H) Cable eléctrico/ Enchufe de la luz (I) Pantalla de lámpara NOTA: (J) Anillo de pantalla Use el destornillador (K) Bombilla de luz con el tornillo del (no incluida) conjunto preinsta -...