Option 1: Weedkiller; Option 2: Cleaning - Batavia SteamBoxxer Mode D'emploi

.
English
7. FOR THE BEST RESULTS THE PRES-
SURE ON THE MANOMETER SHOULD
BE BETWEEN 2.5 AND MAX.
If the pressure is below 2.5 bar, it is advice
to stop and let the pressure again go up to
maximum. This steam pressure build-up
time should take no longer than 40
seconds.
8. If the steam trigger is pressed when the
orange light is on, hot water may come out
of the steam gun.

OPTION 1: WEEDKILLER:

Assemble the extension handle:
The extension handle consists of two parts.
Connect both parts and tighten the
connection.
Attach the extension handle to the steam gun.
Make sure that the extension firmly clicks into
position. If using the device as a weed killer
you must use the extension handle. (Fig. F)
1. For weed and moss between tiles and for
use in vegetable/kitchen gardens, use
weed cone (16). Apply the cone over the
weed. Apply the steam trigger for 3 - 4
seconds and move the cone to next weed.
During these few seconds the cell struc-
ture of the weed is destroyed. As a result,
the weed dies within a few days.
2. For weed/moss in wider gaps, attach the
pin nozzle (12). Apply the pin nozzle into
the weed/moss and apply the steam trig-
ger for 3-4 seconds, move it to next weed.
The weed/moss dies within a few days.
3. For weed in the lawn, use the 3-pin nozzle.
Apply the 3-pin nozzle over the centre of
the weed and push it to full insertion into
the ground. Apply the trigger for 5-6 sec-
onds. Due to the patented construction
the steam will kill the root of weed. Move it
to next weed. Using this 3 pin nozzle will
only leave the weed terminated and not
the grass. The weed dies within a few
days.

OPTION 2: CLEANING

Assembling and attaching small brush, large
brush, jet nozzle, window cleaner (Fig. G):
1. Make sure the machine is unplugged from
the mains
14
7062741_SteamBoxxer_Ma-#1612-05.indb 14
2. Attach the straight adapter to the steam
gun
3. Make sure that the straight adapter firmly
clicks into position.
4. Select the accessory needed and slide the
accessory onto the straight adaptor.
Assembling and attaching Floor brush:
1. Make sure the machine is unplugged from
the mains
2. Assemble the extension handle:
– The extension handle consists of two
parts. Connect both parts and tighten the
connection.
– Attach the extension handle to the steam
gun. Make sure that the extension firmly
clicks into position. If using the floor brush
accessory you must use the extension
handle.
3. Attach the floor brush adaptor to the floor
brush. The adaptor must be angled down.
(Fig. H)
4. Rotate the floor brush adaptor 90° to set
into place (Fig. I)
5. Attach the extension handle to the floor
brush adaptor, make sure that the exten-
sion firmly clicks into position.
Attaching the cleaning cloth to the floor
brush:
Warning! Never remove the cleaning cloth
while the machine is in operation!
1. Put the cleaning cloth on a flat surface
2. Place the floor brush over the cleaning
cloth
3. Press down on a clip on the floor brush
and fold the end of the cleaning cloth
beneath the clip. Release the clip to fasten
the cloth into place. Repeat for the oppo-
site side. (Fig. J)
The floor brush and cleaning cloth are perfect
to use on the following hard floor surfaces:
Stained Concrete, Linoleum, Marble, Granite,
Ceramic tile, vinyl.
Warning: Do not use on unsealed hard wood,
laminate flooring or unglazed ceramic sur-
faces. Surfaces that are not properly sealed
may be warped or damaged by exposure to
heat and moisture. Always test a small area
before beginning.
06-12-16 14:16