Publicité

Model #
597KFDW1
Crescent Nightstand
Assembly Instructions
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload drawers on this unit.
For maximum stability, attach unit to the wall
using the enclosed hardware as per instructions.
Presented by Whittier Wood Products
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
We will replace any
parts which are defective, missing or
damaged during assembly. Please contact
Whittier Wood Products customer service
department directly (by phone, fax, mail or
email) for replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter/number, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • Email: info@whittierwood.com
Fax: 541-687-2060 • Email: info@whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place;
3) in temperatures ranging from 40° to 90°.
(Not on a cold, possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
Rev. 10/05

Publicité

Table des Matières
loading

Sommaire des Matières pour Whittier Wood Products Chaparral Crescent 597KFDW1

  • Page 1 Assembly Instructions Service Policy: We will replace any parts which are defective, missing or damaged during assembly. Please contact Whittier Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts. Hours: Our friendly customer service staff can be reached Monday-Friday 7:00 a.m.
  • Page 2 597KFDW1 Crescent Nightstand — Parts List BEFORE BEGINNING ASSEMBLY, check that the quantities of the parts received match those on the parts list. 1 — Top — Qty. 1 2 — Back — Qty. 2 3 — Left Side — Qty. 1 5 —...
  • Page 3: Tools Required

    ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: Phillips Screwdriver, Mallet or Padded Hammer, Wood Glue, Tape Measure STEP 1 x 18 1. Glue three Dowels (A) in the tops of the Left and Right Sides (3 & 4) and two in both ends of Front and Rear Sleepers (9 & 11). 597KFDW1 –...
  • Page 4 STEP 2 x 03 lue do els in sleepers into the holes in the eft ide he pocket drilled holes in the rear sleeper must e on the outside of the unit. nsert a mm hillips an ead cre in the pocket drilled holes in the ottom of the front sleepers and in ack of the rear sleeper.
  • Page 5 STEP 4 Insert the dowels in the top edge of the Sides into the holes in the Top (1). Fasten in place with 4 x 35mm Phillips Pan Head Screws (F) through the holes in the side cleats. STEP 5 Place the Backs (2) on back of the unit with the Back Channel (12) between them.
  • Page 6 STEP 6 ttach ra er ides ith slide heels to the rear and rooves for dra er ottom ali ned to the ra er ront ith . mm hillips cre s lide the ra er ottom into rooves in dra er side and attach the ra er nd ith cre s ttach a no to each dra er ith a...
  • Page 7 TIPPING RESTRAINT Your unit comes with a tipping restraint to help prevent the unit from falling forward should a child attempt to climb on it. Please follow the instructions provided below. TIPPING RESTRAINT Attach tipping restraint to the center of the top back edge of your unit. Follow these instructions and use the hard are contained in the packet provided.
  • Page 8 Para màxima estabilidad, sujete la unidad a la pared utilizando los accesorios que se incluyen y siguiendo las mismo. Apriete los tornillos o repare las piezas según instrucciones. corresponda. Código del producto P.O. Box 2827 Eugene, OR 97402 USA Rev. 10/05 Presentada por Whittier Wood Products...
  • Page 9: Lista De Piezas

    597KFDW1 Mesita de Noche Crescent LISTA DE PIEZAS Antes de comenzar a armar, verifique que haya recibido todas las piezas que se listan en la lista de piezas que se presenta a continuación. Cant. Cant. Cant. 11 Travesaño trasero ....01 Panel superior ......
  • Page 10 Ne pas surcharger les tiroirs de cet article d’ameublement. Pour une stabilité maximum, fixez l’unité au mur a l’aide du petit outillage fourni, en suivant les instructions. Code produit P.O. Box 2827 Eugene, OR 97402 USA Rév. 10/05 Présenté par Whittier Wood Products...
  • Page 11: 597Kfdw1 Ta Le De N It Crescent

    597KFDW1 Ta le de N it Crescent NOMENCLATURE DES PI CES AGE v rifiez si la quantit des pi ces re ues correspond la liste ci dessous. té té té is cruciforme t te 11 Travesse arri re ....01 Dessus ........
  • Page 12 Presented by Whittier Wood Products 1. Choose a finish that will meet your expectations for the product you are finishing. Are you matching existing furniture or do you want a “natural” finish? Is the piece to be functional, decorative or both? The answers Rubber gloves to these questions may affect the type of finish you choose.
  • Page 13 Gluing Hints (cont.) 3. We recommend that you use a good wood glue, such as Elmer’s Wood Glue or White Glue, Tite- bond Wood Glue or the equivalent; unless the instructions call for a special type such as a slow drying epoxy glue.
  • Page 14 Presentada por Whittier Wood Products 1. Elija un acabado que cumpla con las expectativas para el producto a ser acabado. ¿Debe hacer juego con otros muebles o se desea un acabado “natural”? ¿Ha de Guantes de caucho ser funcional, decorativo o ambas cosas? Las respuestas a estas preguntas pueden Trapos afectar el tipo de acabado que se seleccione.
  • Page 15 Ayudas Para el Pegamento: (cont.) 3. Recomendamos que utilice una buen pegamento de carpintero, como Elmer’s Wood Glue o White Glue, Titebond Wood Glue o su equivalente. Lea el rótulo del fabricante cuidadosamente y siga todas las instruc- ciones. 4. Asegúrese de que los agujeros estén libres de polvo para que el pegamento tenga una superficie limpia a la cual adherirse.
  • Page 16 Présenté par Whittier Wood Products 1. Choisissez un enduit de finition qui réponde à ce que vous attendez du meuble. Souhaitez-vous l’harmoniser à votre mobilier actuel ou voulez-vous un aspect naturel ? Le meuble est-il destiné à être fonctionnel, décoratif ou les deux ? Le type Gants en d’enduit de finition que vous choisissez dépend des réponses à...
  • Page 17 Conseils de Finition (suite) 3. Nous vous recommandons d’utiliser une bonne colle à bois, par exemple Elmer’s Wood Glue ou White Glue, Titebond Wood Glue ou équivalent, sauf si les instructions préconisent un type spécial de colle, par exemple une colle époxyde à durcissement lent. Lisez attentivement l’étiquette du fabricant et suivez toutes les instruc- tions.

Table des Matières