Rupes BA31ES Conversion Des Instructions De Fonctionnement Original page 12

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
REPLACING THE ABRASIVE DISCS
This can be done in one of two ways:
1. Mode:
lock the wheel holder shaft (5) pushing button (4) simultaneously
rotating the abrasive disc holder sanding pad (12) until alerted of its
locking. Unlock the wheel spindle by releasing the buttonand rotate the
wheel by hand to ensure that it runsfreely. Release the wheel holder
shaft by releasing the button and manually rotating the abrasive disc
holder sanding pad to control its unlocking.
WARNING!: never press the wheel spindle locking button until
the tool has stopped moving and is perfectly stationary; the gear
box or the push button pin could be broken and the guarantee
would be invalidated.
2.Mode
insert the 17 mm wrench (13) into the pocket of the shaft between
the abrasive disc holder sanding pad and the gear box to lock the
wheel holder shaft (5). Proceed as in the 1st mode: "Unscrew the ring
nut [...]"
Tools other than those mentioned must not be used for slackening for
tightening purposes.
WARNING: Before use, check the state of the wheel. The wheels
must be properly assembly and must rotate freely rotate freely.
Never use defective or damaged wheels/cutters. Defective
wheels can fall to pieces and cause dangerous incidents.
Start the tool and check that there are no unusual vibration, no dismatching
movement of the abrasive disc. Otherwise switch-off the tool immediately and
eliminate the cause.
STARTING AND STOPPING
- Starting: push the slide of the ON/OFF (2) forward; if the tool is to be locked in
the ON position, apply pressure to the front part of the slide switch at the same
time.
- Stopping: release the slide ON/OFF (2).
If locked, press the ON/OFF switch in the lower part downwards and release it
in the OFF position.
WARNING: after an interruption of the electrical energy, if the
ON/OFF switch is inserted, it is necessary to release the switch
(see Stopped).
ELECTRONIC RPM REGULATION
The rpm can be adjusted by rotating the speed adjustment wheel(3) located on
the rear of the tool. The choice of speed depends on the characteristics of the
abrasive paper disc and the material to be worked.
ACCESSORIES
Abrasive discs Ø 115 mm.
The use of tools of larger diameter will overload the motor and
drive system leading to rapid deterioration.
12
MAINTENANCE
All maintenance operations are carried out with the power supply
disconnected. At the end of each work session, or when required,
remove any dust from the body of the tool using a jet of compressed
air, paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by the user.
Maintenance and cleaning of the inner parts, like brushes, ball bearings, gears
etc. or others, must be carried out only by an authorized customer-service
workshop or on www.rupes.com.
Use only the original RUPES parts or accessories.
DISPOSAL
For EC countries only: According to the European Directive on Waste
from electrical and electronic equipment and its implementation in
conformity with national standards, exhausted electrical equipment
must be collected separately, in order to be recycled in an
environmentally friendly way. The product, when it reaches the end of
its life, must not be dispersed in the environment or thrown away as household
waste. It must be disposed at authorized recycling centres (contact your local
authorities to know where to dispose of the product according to the law). The
correct disposal of the product contributes to the health and preservation of the
environment.
Illegal disposal of the product will entail penalties against the offenders.
Disposing of the product correctly contributes to protecting human health and
safeguarding the environment. Any illegitimate disposal of the product will be
punishable by law.
CONFORMITY DECLARATION
We declare on our responsability that the hand-held motor operated tool, which
is mentioned in the present operating manual, is in comformity with the Essential
Requirements of Safety of the following Directives:
2006/42/EU; 2014/35/EU; 2014/30/EU; 2011/65/EU
The tests have been carried out in accordance with following Standards:
EN 60745-1-2009 + A11:2010
EN 60745-2-3:2011 + A2:2013 + A11:2014 + A12:2014 + A13:2015
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2013
EN 62233: 2008
Technical file at:
RUPES S.p.A.
Via Marconi, 3A - Loc. Vermezzo
20080 VERMEZZO CON ZELO (Mi) - Italy
Vermezzo con Zelo (MI), 22/05/2016
S.p.A
IL PRESIDENTE
G. Valentini

Publicité

Table des Matières
loading

Table des Matières