Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Bumper bracket
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75691F
Wrenches: Open end 3/4 wrench & 7/8"
Bumper
bracket
1 2
Figure 1
N
Note: Fasteners typical
F
both sides
1
Qty. (4)
Hex bolt, 1/2-13 X 2.0 Gr5
2
Qty. (8)
Conical washer
3
Qty. (4)
Hex nut, 1/2-13
Removal of the spare tire can make installation easier, however, removal not necessary.
1.
Raise hitch into position as shown in Figure 1. Use fasteners to attach the hitch uprights to the bumper bracket.
2.
Attached remaining fasteners as shown. Item 4 must be sandwiched inside slot on bumper bracket. The hitch brackets and
the vehicle bracket will be drawn together.
3.
Torque all fasteners to specifications shown below.
4.
Reinstall spare tire, if it was removed prior to hitch installation. Make sure spare tire does not contact bolts.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
Bumper
Bumper bracket one piece.
Shown broken for clarity
2 3
Hitch side
bracket.
i l
1 2
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Ford F-150
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Round spacer
washer (Item 4) fits
into slot on bumper
bracket
3 2
2
3
2
Hitch uprights
4
Qty. (2)
Spacer round
5
Qty. (2)
Spacer ¼" X 2.50 X 1.75
Sheet 1 of 3
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
12,000 (5448 Kg)
6000 (2724 Kg)
Wiring Access Location: PC3
4
5
2
Figure 2
1
Item 4 must be sandwiched
inside slot on bumper
bracket.
75691N
3-12-10
Part Numbers:
75691
87583
44645
Max Tongue
WT (LB)
1200 (545 Kg)
600 (272 Kg)
4
Rev. A
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Performance Products 75691
Sommaire des Matières pour Cequent Performance Products 75691
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75691N 3-12-10 Rev. A 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75691N 3-12-10 Rev. A 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2010 Cequent Performance Products Hoja 3 de 3 75691N 3-12-10 Rev.