Publicité
Liens rapides
140G-K-RMX, 140G-K-NVM_, 140G-K-RVM_, 140G-N7, 140G-N8
Rotary operating mechanism with: external handle or external handle with internal NFPA 79 operating handle
Installation - Installazione - Instalación
Instalação -
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
Cat No.
140G-K-RMX
Cat No.
140U-HM4
140U-HM4E
Cat No.
194R-R7
194R-R8
PN-258432
DIR 1000436R0612 (Version 02)
-
(4) M4 - 50 mm
(2) 4 - 16 mm
Hi-Low
Self Tapping
Cat No.
140G-K-RMX
Cat No.
140U-HM4
140U-HM4E
Cat No.
140G-N7
140G-N8
Cat No.
140G-K-OSB
Bul. 140G/140MG
CLACK
(4) M4 - 50 mm
(2) 4 - 16 mm
Hi-Low
Self Tapping
(2) M4 - 60 mm
Publicité
Manuels Connexes pour Allen-Bradley 140G
Sommaire des Matières pour Allen-Bradley 140G
- Page 1 Bul. 140G/140MG 140G-K-RMX, 140G-K-NVM_, 140G-K-RVM_, 140G-N7, 140G-N8 Rotary operating mechanism with: external handle or external handle with internal NFPA 79 operating handle Installation - Installazione - Instalación Instalação - WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants.
- Page 2 450.8 450.8 194R-S1 140G-N7 (12) (17 - 3/4) (12) (11) (17 - 3/4) 679.4 679.4 194R-S2 140G-N8 (21) (26 - 3/4) (21) (11) (26 - 3/4) (in.) (in.) (5/8) (5/8) Ø 3 Ø 3 (1/8) (Ø 1/8) (1/8) (Ø 1/8)
- Page 3 9.7 lb-in 9.7 lb-in (1.1 Nm) (1.1 Nm) 12.4 lb-in 12.4 lb-in (1.4 Nm) (1.4 Nm) PN-258432 DIR 1000436R0612 (Version 02)
- Page 4 *Minimum distance from hinge to shaft centerline is 76 mm / 3 inches *Minimum distance from hinge to shaft centerline is 76 mm / 3 inches Masking tape Masking tape Du ruban adhésif Du ruban adhésif Abdeckband Abdeckband Cinta adhesiva Cinta adhesiva Fita adesiva Fita adesiva...
- Page 5 BULLETIN 190/194R/140U DRILLING TEMPLATE 190/194R 194R 140U GABARIT DE PERFORATION -HM1 -HM1-N1 -HM1-N2 -HM1-N3 -HM4E BOHRSCHABLONE -HM1E -HM1E-N1 -HM1E-N2 -HM1E-N3 -HM4 PLANTILLA DE PERFORACIÓN -HM4 -HM4-N1 -HM4-N2 -HM4-N3 MODELO DE PERFORAÇÃO -HM4E -HM4E-N1 -HM4E-N2 -HM4E-N3 STAMPO PREFORATO 4 - ø 5.5 mm 4 - 7/32 "...
- Page 6 6 mm (.24 in) Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. PN-258432...