STERWINS PLM1-40B125.4 Mentions Légales & Consignes De Sécurité page 96

4. PARTS DESCRIPTION
Upper handle
1
Starter handle
2
Locking lever
3
4 Grass catcher
5 Locking knob
6 Height adjusting lever
Sideward ap (only for
7
PLM1-51B150.4)
5. TECHNICAL DATA
Model PLM1-40B125.4 PLM1-46B140.4 PLM1-51B150.4
Engine type B&S 300
Self-propelled Yes
Engine displacement
125 cm³
Nominal power
1.7 kW
Cutting width
40 cm
Blade type DAYE 26300100401
Blade tightening torque 44~46 N.m
Rated speed 2800/min
Oil tank capacity 470 cm
Fuel tank capacity
800 cm
Grass catcher capacity
50 L
Net weight
26,6 kg
Height adjustment 25~75 mm,
7 adjustment
Measured sound pressure 80,5 dB (A)
level at operator's position k=3 dB (A)
Measured sound power level
91,1 dB (A)
k= 2,25 dB (A)
Guaranteed sound Power level
96 dB(A)
Vibration 6,55 m/s²
k=1,5 m/s²
EN
Side discharge channel (only for
8
PLM1-51B150.4)
Spark Plug
9
10 Fuel cap
11 Oil cap
12 Cable clamp
Self-drive control handle
13
14 Brake control handle
B&S 500E B&S 625E
Yes Yes
140 cm³ 150 cm³
1.9 kW 2.2 kW
46 cm 51 cm
DAYE 263001465 DAYE 263001330
44~46 N.m 44~46 N.m
2800/min 2800/min
470 cm 470 cm
800 cm 800 cm
60 L 60 L
29,8 kg 31,6 kg
25~75 mm, 25~75 mm,
7 adjustment 7 adjustment
84,3 dB (A) 83,7 dB (A)
k=3 dB (A) k=3 dB (A)
94,5 dB (A) 94,6 dB (A)
k= 1,91 dB (A) k= 1,94 dB (A)
96 dB(A) 98 dB(A)
6,94 m/s² 7,94 m/s²
k=1,5 m/s² k=1,5 m/s²
7
In you encounter some problems with this tool, please follow these solutions.
If you cannot resolve your problem, please contact our service agent.
1. Engine does not start:
•Fill tank with fuel.
•Clean air cleaner element.
•Tighten spark plug.
•Install spark plug wire on spark plug.
•Set gap between electrodes (customer service center).
•Install new, correctly gapped plug.
•Remove air cleaner element and pull starter rope continuously until carburetor
clears itself and install air cleaner element.
2. Engine di cult to start or loses power:
•Drain fuel and clean tank. Fill tank with clean, fresh fuel.
•Clean or replace fuel tank cap.
•Clean air cleaner element.
3. Engine operates erratically:
•Install new, correctly gapped plug.
•Set gap between electrodes (customer service center).
•Clean air cleaner element.
4. Engine idles poorly:
•Clean air cleaner element.
•Remove debris from slots.
•Remove debris from cooling ns and air passages.
5. Engine skips at high speed:
•Set gap between electrodes (customer service center).
6. Engine overheats:
•Remove any debris from slots in shroud, blower housing, air passages.
7. Mower vibrates abnormally:
•Tighten blade.
•Balance blade.
8
6. TROUBLES SHOOTING
EN