Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
INSTALLATION INSTRUCTIONS:
1. Remove OEM cab skirts
2. Loosely install front mounting bracket to the cab skirt using the supplied 10-32 X 1/2" carriage bolts, washers, and locknuts.
(Driver side shown in the image)
3. Install rear mounting bracket to the cab using the supplied 1/4-20 X 1/2" hex head bolt, 1/4" lock washer.
4. Hold the cab skirt aligning the rear contour of the cab skirt to the truck and mark the location of mounting hole
5. Drill 3/16" hole in the marked location.
6. Install cab skirt on the truck with supplied 1/4-20 X 3/4" hex head bolts, flat washers, and lock nuts on the locations marked in
the image below. Do not fully fasten.
7. Fasten the rear potion of the cab skirt to the rear bracket and the drilled hole with supplied 10-32 X 1/2" truss head screws, flat
washers, and lock nuts.
Page 1 of 6
CAB SKIRT
Western Star 47X Daycab
2
3
4-5
00813095
Mark
Alig
7
12/2022
Publicité
Manuels Connexes pour Panelite DIETER'S Western Star 47X
Sommaire des Matières pour Panelite DIETER'S Western Star 47X
- Page 1 CAB SKIRT Western Star 47X Daycab INSTALLATION INSTRUCTIONS: 1. Remove OEM cab skirts 2. Loosely install front mounting bracket to the cab skirt using the supplied 10-32 X 1/2" carriage bolts, washers, and locknuts. (Driver side shown in the image) 3.
- Page 2 8. Fully tighten the front mounting bracket to the cab, and then the cab skirt to the mounting bracket. Control the gap between the skirt and the cap while tightening. 9. Fully tighten the rest of the fasteners. 10. Peel the plastic from the cab skirt and clean with glass cleaner, if necessary. Page 2 of 6 00813095 12/2022...
- Page 3 JUPE DE CABINE Western Star 47X Cabine de jour INSTRUCTIONS D’INSTALLATION: 1. Retirez les jupes de cabine OEM 2. Installez sans serrer le support avant à la jupe de cabine avec les boulons de carrosseries 10-32 X 1/2", rondelles et contre- écrous.
- Page 4 8. Serrez complètement le support avant à la cabine, puis serrez la jupe de cabine au support. Contrôlez l’écart entre la jupe et la cabine tout en serrant. 9. Serrez complètement toutes les autres fixations. 10. Retirez la pellicule plastique de la jupe de cabine et nettoyez avec un nettoyant à vitre, si nécessaire. Page 4 of 6 00813095 12/2022...
- Page 5 FALDA DE CABINA Western Star 47X Daycab INSTRUCCIONES DE INSTALACIÓN: 1. Quite las faldas de cabina OEM. 2. Flojamente, instale el soporte de montaje frontal a la falda de cabina usando los tornillos provistos 10-32 X 1/2", arandelas y tuercas. (La imagen muestra el lado del piloto) 3.
- Page 6 8. De forma completa, apriete el soporte de montaje frontal a la cabina, y la falda al soporte de montaje. Controle el espacio entre la falda y la tapa mientras aprieta. 9. Apriete completamente el resto de sujetadores. 10. Quite el plástico de la falda de cabina y limpie con limpiador de vidrio, si es necesario. Page 6 of 6 00813095 12/2022...