CDVI DGLP WLC Manuel D'installation page 3

INSTALLATION MANUAL
DGLP WLC - DGLP FN WLC - DGLPM WLC - DGLI WLC - DGLI F WLC
Proximity Card Readers - Wiegand Output
4] WIRING DIAGRAM : DGLP WLC, DGLI WLC, DGLP FN WLC et DGLI F WLC
ST5 : Wiegand output selection
ST4
Output format:
- ST5 in 1: 26 bits Wiegand*
ST5
- ST5 in 2: 30 bits Wiegand
- ST5 in 3: 44 bits Wiegand
1 2 3
ST4
ST4
DGLP WLC and DGLI WLC
ST4
ST5
ST5
ST5
1 2 3
1 2 3
T4
26 Bits 30 Bits
ST4
ST4
ST4
ST4
ST5
DGLP FN WLC and DGLI F WLC ST5
ST5 ST5
1 2 3
3 1 2 3
2
T4
ST4
1
4
ST4 ST5
26 Bits 30 Bits
ST5 ST5
1 2 3
* Not necessary in 26 bits format for the new
3
product manufactured since January 2008
2
T4
(26 bits as standard).
1
4
ST5
DGLP FN WLC and DGLI F WLC
3
Wiring :
2
1
Red Input voltage 12VDC
Black 0V
Blue Clock
Green Data 0
White Data 1
Brown Buzzer
Yellow Green LED
Orange Red LED
DGLP WLC and DGLI WLC
Terminal (8 pins) :
+ Input voltage 12VDC
- 0V
H Clock
D0 Data 0
D1 Data 1
B Buzzer
V Green LED
R Red LED
ST5
1 2 3
ST5
ST5
3
1 2 3
2
1
ST5
ST5
3
3
1 2 3
2
2
44 Bits
1
1
ST5
3
3
2
2
1
1
44 Bits
3
2
1
D698_01
ST4
+ -
H D0
Open collector outputs
Switches : I1 and I2
D695ED2
The buzzer and the LED's can be controlled
by the reader or by an external device. They
can be controlled together or separately.
Note: In case the buzzer and the LED's are
not controlled by a device, when a card is
placed within the RF field of the reader
ON
and the signal of the card is valid then the
I1 I2
buzzer emit a tone and the LED switches
OFF
from Red to Green.
ST5
3
2
Configurations:
1
ST4
SWITCH I1 = ON
Buzzer External mode (Operations
programmed via the Centaur Access
Control Software or another controller)
SWITCH I1 = OFF
Buzzer Internal mode (Defaults
operations programmed in the reader)
ON
SWITCH I2 = ON
LED External mode (Operations
I1 I2
programmed via the Centaur Access
OFF
Control Software or another controller)
SWITCH I2 = OFF
LED Internal mode (Defaults
ST5
operations programmed in the reader)
1 2 3
Important: I1 and I2 switches configu-
ration are set when power is applied in
to the reader. Internal mode, B, V and
R inputs are not set.
D1 B
V R
ST5
ST4: Pulls up 12 V or 5V
Open collector outputs: 1 2 3
ST4
12V 5V No pull up
ST5
1 2 3
ST4
ST4
Select the output voltage
ST5
according to the installation.
1 2 3
ST4
ST4
ST4
ON
I1 I2
OFF
ON ON
I1 I2 I1 I2
OFF OFF
ON ON ON
I1 I2 I1 I2 I1 I2
OFF OFF OFF
cdvi.com
cdvigroup.com
ST5
1 2
ST4
ST5
1 2
ST4
ST5
ST5
1 2
1 2 3
ST4
ST5
1 2 3
ST5
1 2 3
ON ON O
I1 I2 I1 I2 I1
OFF OFF O
ON ON O
I1 I2 I1 I2 I1
OFF OFF O
ON ON
I1 I2 I1 I2
OFF OFF
ON
I1 I2
OFF
3