Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

MODEL: OD45-9005
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from
being switching on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
c.Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
d.Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and
the local code authorities.
e.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
f. Ducted fans must always be vented to the outdoors.
g.Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit (ceiling
installation only).
h.This unit must be grounded.
i. Not for Use in Kitchens.
j. To reduce risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into spaces within walls or ceilings
or into attics, crawl spaces, or garages.
k.WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.
l. The fan must not be installed in a ceiling thermally insulated to a value greater R40.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. This product is designed for installation in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must point up.
DO NOT MOUNT THIS PRODUCT IN A WALL.
3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off
power unit.
4. Please read specification label on product for further information and requirements.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appearance - lower or remove grille and vacuum interior of unit
with the dusting brush attachment.
The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noi-
ses, replace the motor with the exact service motor. The impeller should also be replaced.
OPERATION
The fan continues to run at the preset lower speed of 45 CFM. When the switch is turned on, the fan will run at high speed.
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner.
info@ortechindustries.com
www.ortechindustries.ca
OD45-1109
13376 Comber Way
Surrey BC V3W 5V9
VENTILATION FAN
205 Summerlea Rd
Brampton, ON L6T 4E5
1-888-543-6473
1-888-541-6474

Publicité

Table des Matières
loading

Sommaire des Matières pour Ortech OD45-9005

  • Page 1 VENTILATION FAN MODEL: OD45-9005 OD45-1109 WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. b.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switching on accidentally.
  • Page 2: Plan The Installation

    PLAN THE INSTALLATION 1. Do not use in a cooking area. 2. Two ways to connect ductwork to a factory-shipped unit. INSULATION* ROOF CAP* (Place around and (with built-in over Fan Housing.) damper) POWER HOUSING CABLE* Keep duct runs short Seal gaps around Housing.
  • Page 3 ASSEMBLY INSTRUCTIONS 3. ATTACH DAMPER/DUCT CONNECTOR DUCT Snap the damper/duct connector onto the fan housing. The connector must be flush with the top of the housing, and the damper flap should fall closed. Insulated flexible duct is recommended for the quietest possible installation. If rigid duct is used, a short (1-3 feet) section of insulated flexible duct will ensure quiet operation 4.
  • Page 4: Service Parts

    INSTALL GRILLE Install ceiling material to complete the ceiling construction. Then, cut around the fan housing. To attach the grille assembly to the fan housing, pinch the grille springs on the sides of the grille assembly, and position the grille into the housing with the grille springs in the appropriate slots.
  • Page 5: Ventilateur

    VENTILATEUR MODÈLE: OD45-9005 OD45-1109 AVERTISSEMENT Utilisez cet appareil uniquement de la manière prévue par le fabricant. Si vous avez des questions, contactez le fabricant à l'adresse ou au numéro de téléphone figurant dans la garantie. Avant de réparer ou de nettoyer l'appareil, éteignez celle-ci au panneau de service et verrouillez-le pour empêcher l'alimentation accidentelle.
  • Page 6: Planifie Votre Installation

    PLANIFIE VOTRE INSTALLATION TYPES INSTALLATIONS INSTRUCTIONS 2. MONT 1-888-543-6473 205 Summerlea Rd 13376 Comber Way info@ortechindustries.com Brampton, ON L6T 4E5 1-888-541-6474 Surrey BC V3W 5V9 www.ortechindustries.ca...
  • Page 7: Branchement Des Fils Électriques

    INSTRUCTIONS 3. ATTACH 4. INSTALL ROND BRANCHEMENT DES FILS ÉLECTRIQUES Relier le circuit électrique de votre maison de 120 V c.a. à l’emplacement du ventilateur. Utilisez seulement des raccords homologués par UL pour relier le circuit électrique de votre maison à la plaque de câblage. Branchez les fils comme illustré...
  • Page 8: L'installation De La Grille

    L’INSTALLATION DE LA GRILLE Pincez ensemble les ressorts de la grille et insérez-les dans la plaque du moteur dans le boîtier. Poussez la grille fermement vers le plafond. Pour fixer la grille au boîtier du ventilateur, pincez les ressorts se trouvant sur les côtés de la grille, puis installez la grille dans le boîtier en insérant les ressorts dans leurs fentes respectives.

Ce manuel est également adapté pour:

Od45-1109

Table des Matières