ASC PRESIDENT JFK II Manuel D'utilisation page 34

To memorize:
- press MEM shortly; «MEM» is blinking.
- press during 1 second M1, M2, M3, M4,M5 or M6. «MEM» becomes permanent
and the number of the memory appears on the display. The channel is
memorized. If the Beep function is activated a long beep confirms the saving.
In order to display the frequency press FRQ (the memory number is hidden).
To recall a memory:
- press MEM shortly, «MEM» is blinking.
- press M1, M2, M3, M4, M5 or M6 shortly.
- «MEM» is permanently displayed and the memory number appears on the
display. The memorized channel is active.
To delete a memory:
- switch off the transceiver
- keep the key M1, M2, M3, M4, M5 or M6 pressed and switch on the transceiver
- the selected memory is deleted.
F - FREQUENCY BAND SELECTION
(configuration: E; d; EU;EC; U; PL)
The frequency bands have to be chosen according to the country of use.
Don't use any other configuration. Some countries need a user's licence.
See the configurations/ frequency bands table at page 51.
Proceeding: switch off the transceiver. Keep the key F pressed and switch on
again. and the letter corresponding to the configuration are blinking.
- In order to change the configuration, use the channel selector on the front
panel or the UP/DN keys of the microphone.
- When the configuration is selected, press 1 second on the F key.
letter corresponding to the configuration are continuously displayed. At this
point, confirm the selection by switching off the transceiver and then switch-
ing it on again.
See table page 51.
15) NB/ANL ~ SCAN ~ M3
NB/ANL
(short press)
Noise Blanker/ Automatic Noise Limiter. These filters allow reducing back
ground noises and some reception interferences. A press activates the filters
in following order: NB off, ANL off  NB off, ANL on  NB on, ANL off  NB on,
ANL on.
(long press)
and the
«NB» and/or «ANL» are displayed in accordance with the selected configuration.
In FM mode only the NB filter is active.
SCAN
(long press)
Channel research: Allows activating the SCAN function (research of the
channels) in an increasing way. «SCAN» is displayed. The scanning stops as
soon as there is a busy channel. The scanning automatically starts 3 seconds
after the end of the transmission and no key is activated during 3 s. The
scanning starts again in an increasing way by turning the rotary knob to the
right or pressing the UP key of the microphone, or in a decreasing way by
turning the rotary knob to the left or pressing the DN key of the microphone.
Memories research: Press MEM during the channel research cycle. The
transceiver scans the active memories (M1,M2,M3,M4,M5,M6) and channels
19 and 9. Press MEM again to return to the channel research cycle.
A new long press on SCAN disables the SCAN function.
M3
See § 14 MEM.
16) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the setting
of the equipment into the dashboard easier.
See cabling diagram page 50.
17) PTT
Transmission key, press to transmit a message,
listen to an incoming communication.
BEEP
(changing the channel, keys etc.)
In order to activate the BEEP function, turn on the transceiver by pressing the
UP key of the microphone. «BP» is displayed. In order to disable the function,
turn the transceiver on by pressing the DN key of the microphone. «BP»
disappears.
A) POWER SUPPLY (13.2V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR OPTIONAL VOX MIKE (2.2 K Ω Ω Ω Ω Ω Electret, Ø 2.5 mm)
34
is displayed and release to