Sensor Coverage Area; Cleaning And Care; Important; Technical Data - Sygonix 2377679 Mode D'emploi

6.3 Sensor coverage area

If the connected light is ≥ 60 W, the distance between light and sensor should be ≥ 60 cm.
50º
15 m
360º
5 m
5 m
6.4 Motion sensor (PIR)
The passive infrared (PIR) motion sensor reacts to changes in temperature, e.g. when a person or animal
enters the detection area.
■
Position the sensor so the object moves across the detection area.
■
The correct installation height should be observed.
■
Do not point the sensor at radiators, lights, or objects with varying temperatures (e.g. electronic equip-
ment), and objects that may move due to the flow of air. This may trigger the sensor unintentionally.
■
Do not install the product behind glass.
■
Keep the sensor away from direct sunlight.
7 Operation
7.1 Switch-on time "TIME"
■
Control how long the connected the load stays ON after the sensor
is triggered.
■
If new motion is detected during the switched-on time, the timer will
restart.
■
See section "Technical data, PIR sensor time delay".
■
Dial settings:
– Counter clockwise: decrease the duration.
– Clockwise: increase the duration.
7.2 Switching threshold "LUX"
■
You can adjust the switching threshold for different ambient light
levels.
– Counter clockwise: activates motion detection in darker condi-
tions.
– Clockwise: activates motion detection in brighter conditions.
8 Troubleshooting
Problem Possible causes
■
Connected load
Check the LUX setting, it should correspond to ambient light levels. E.g., if it
does not switch is set too high the sensor will not trigger in the dark.
ON. ■
Check the power supply is functioning correctly.
■
Check if the connected device (e.g., lamp) is functioning correctly.
■
Movements within the detection area are too rapid and are filtered out by the
electronic system to prevent switching errors.
■
Motion detection is The ambient temperature is too high.
not functioning cor- ■
There are obstructions preventing the sensor from detecting heat sources
rectly
(e.g., glass).
■
Check that if there are induction sources within detection area.
■
Observe the correct installation height. See section "Technical data" for fur-
ther information.
■
The connected load Constant movements are occurring within the detection area.
is always ON. ■
New movement is detected before the previous switch-ON time has elapsed.
Try setting a shorter time interval.
4
50º
160º
15 m

9 Cleaning and care

Important:

The product is generally maintenance-free. Any repair or maintenance work must be carried out by a
specialist.
Clean the product with a dry, fibre-free cloth.
NOTICE! Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
10 Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

11 Technical data

Operating voltage .................................. 220 – 240 V/AC 50/60 Hz
Rated load .............................................. max. 2000 W resistive (e.g. incandescent lamp)
Power consumption ............................... 0.59 W (static)
PIR sensor activation ............................. 3 – 2000 lux (adjustable)
PIR sensor time delay (adjustable)......... 10 sec ±3 s to 15 min± 2 min
PIR sensor detection range ................... max. 15 x 5 m
PIR sensor detection angle ................... Vertical: Left 50°, right 50°, center 160°
PIR sensor installation height ................ 2.2 - 4 m
Protection class ...................................... II
Operating humidity ................................ <75 % RH
Operating temperature .......................... -5 to +30 °C
Storage humidity .................................... <93 % RH
Storage temperature .............................. -20 to +40 °C
Product dimensions (Ø x H) .................. 103 x 53.5 mm
Weight (approx.) .................................... 143 g
ø103 mm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2377679_V3_0122_dh_mh_en pj-id: 18014398747176331-1 i/o: I3/O3 edtl-id: en
max. 1000 W inductive (e.g. energy-saving lamp or LED)
0.70 W (active)
Horizontal: Left 110°, right 110°, center 360°