AquaScape 84057 Instructions Et Entretien page 2

• Connect lights to Aquascape color-changing
splitters and extensions (Ex. 5).
NOTE: Quick-connect connections must
be fully tightened to prevent water from
entering. Dielectric grease, available at most
home improvement stores, can be used in all
connections to further prevent water infiltration.
• For installations with existing low-voltage
lighting or components, split the power after
the transformer, before the color-changing
lighting control hub, to run color-changing
lights with the existing transformer (Ex. 6).
WARNING: Do not submerge quick-
connect fittings, as moisture entering
the connections will damage the lights.
COLOR-CHANGING LIGHTING CONTROL HUB
• The Aquascape Color-Changing Lighting
Control Hub (not included) is required to power
and control Aquascape color-changing lights
(Ex. 7).
• Connect the light, splitter, or extension to the
5-pin quick-connect fitting attached to the hub
(Ex. 8).
NOTE: Each control hub can control up to
150-watts of color-changing lights.
NOTE: Only one remote can be paired to a
single hub.
NOTE: Multiple Color-Changing Lighting Hubs
and remotes can be used to assign multiple
colors simultaneously.
NOTE: The control hub is weather resistant,
but not waterproof. Install it off the ground and protected from the
elements.
TRANSFORMER SETUP
• Aquascape color-changing lights are designed to operate on a 12-volt,
outdoor-rated transformer.
WARNING: Aquascape color-changing lights have a max
voltage operating range between 10.8 and 15 volts. Operating
the light outside of this voltage range voids the product warranty
and may damage or shorten the life of the light.
NOTE: It is recommended to locate the
transformer as close to the light fixtures as
possible to avoid voltage drops caused by long
cable runs.
• Plug the transformer into a GFCI-protected
outlet (Ex. 9).
REMOTE CONTROL PAIRING
• Each control hub includes a wireless remote control. Install two AAA
batteries (not included) in the back of the remote control.
• To synch the remote
control to the hub,
hold the power button
on the remote while
connecting the 2-pin
quick-connect fitting
on the hub to the
transformer (Ex. 10).
• All lights plugged into the control hub will flash green when paired.
• Once the remote is synched to the control hub, bury or conceal any
visible cables. It is recommended to bury light cables no deeper than 6".
2
REMOTE CONTROL FUNCTIONS
• Power/Pair – Turn lights on and off as desired. Also use this button to pair
the remote to the hub.
• Color Wheel – Select your desired color
• Rate/Speed Up – Increase the speed of the cycle or strobe option
• Rate/Speed Down – Decrease the speed of the cycle or strobe option
Ex. 5
• Select Mode – Stops the cycle or strobe to achieve the desired color
• Undo Mode – Revert back to the cycle or strobe last selected
• Brightness Up – Increase the brightness
to color
• Brightness Down – Decrease the brightness
lights
to white
• Cycle – Continuously changes through all available color options
lights
• White – Engages the white diodes for a warm white light (3,000 K)
Ex. 6
• Strobe – Select between a variety of strobe options
General Maintenance
• Periodically clean the fixture with fresh water, removing any existing algae,
debris, or buildup.
Troubleshooting
• Lights won't turn on
– Press the power button on the remote
Ex. 7
– Make sure the outlet is receiving power
– Make sure the ground-fault circuit interrupter (GFCI) is not tripped
– Check to verify that the lights are receiving the correct voltage
– Verify that the photocell (not included) is functioning properly
• Lights won't turn off
– Verify that the photocell (not included) is functioning properly
• Remote Control is not functioning
Ex. 8
– Make sure the AAA batteries are not dead
– Re-synch the remote control to the lighting control hub
Warranty Information
Aquascape LED Color-Changing Fountain Lights are guaranteed for
five years from date of purchase. Proof of purchase required. Warranty
does not cover damage resulting from negligent handling, misuse or
lack of care. Light failure as a result of improper wiring is not covered
under warranty. Lights should only be operated in fresh water without
corrosive chemicals like chlorine or bromine. Warranty is valid against
hazards in handling said material. All applicable laws and regulations
Ex. 9
use of the product, whether defective or not defective, is assumed by
Ex. 10
For more information about our company or products, please visit our website at
12/18
☎
US (866) 877-6637 |
5 YEAR WARRANTY
defects due to material and workmanship only. Products returned
must be cleaned, sanitized, or decontaminated, as necessary, prior
to shipment to ensure that employees will not be exposed to health
shall apply. The sole obligation shall be to replace the defective
unit with a suitable replacement unit. Units should be checked for
proper operation prior to returning as defective. No liability for loss
or damage of any nature or kind, whether arising out of or from the
Aquascape, Inc. or it's affiliates.
aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426
©2018 Aquascape, Inc. • All Worldwide Rights Reserved
☎
CAN (866) 766-3426 | aquascapeinc.com