AquaScape 84057 Instructions Et Entretien

I N S T A L L A T I O N
LED COLOR-CHANGING
FOUNTAIN LIGHT
Aquascape LED Color-Changing Fountain Lights are developed to provide
an impressive accent to fountains. This instruction manual will guide you
through the proper installation of Aquascape color-changing lighting as
well as recommended maintenance procedures to ensure long-term
effectiveness.
LED Color-Changing
Fountain Light
Item #84072
5
Contents - #84057
No. Description
LED Color-Changing
1.
Fountain Light
Required Products
2 1
B B
A A
Color-Changing Lighting
2 1
Control Hub (remote included)
(#84061)
NOTE: The lighting control hub is required to power and control Aquascape color-changing lights.
Each hub can control up to 150-Watts of lights.
Recommended Products
B
3-Way Color-Changing A
Splitter
(#84062)
25' Color-Changing Lighting
Extension Cable
(#84069)
☎
Contact Us
For more information about our company or products,
please visit our website at aquascapeinc.com or call
US (866) 877-6637 CAN (866) 766-3426.
1
12-Volt Transformer
2 1
B
6-Way Color-Changing A
Splitter
2 1
(#84068)
25' 5-Outlet Color-Changing
Lighting Extension Cable
(#84070)
☎ US (866) 877-6637 | ☎
I N S T R U C T I O N S
Safety Information
WARNING: It is recommended
whenever working in or near
water to have all electrical
devices plugged into a ground fault
interrupter (GFCI) that has been
installed by a licensed electrician.
• To reduce the risk of electrical shock
or damage to the light, all wiring and
junction connections should be made
per local codes. Requirements may vary
depending on usage and location.
Model
Dimensions
Voltage Min-Max/Tensions Min-Max
Wattage
Lumens
Kelvin Temperature
Color Rendering Index
Beam Angle Spread
Cord Length
Installation
FOUNTAIN CONNECTION
• Connect fountain tubing/pipe to the barb at the base of the light, using a
twisting motion to secure it in place (Ex. 1).
• Run the tubing down the fountain with the light cable (Ex. 2).
• If desired, the barbed connection can be removed from the light for
installation in tight spaces. Simply thread the barb counter-clockwise until
it disconnects from the light fixture (Ex. 3).
Ex. 1
CONNECT LIGHT FIXTURES
• Aquascape color-changing lights include 5-pin, quick-connect fittings to
provide tool-free electrical connections.
WARNING: Do not cut or remove
the quick-connect fitting or isolation
chamber, as it will damage the
light and void the warranty (Ex. 4).
• Color-changing splitters and extension cables
are available to install multiple lights. See the
recommended products section for available
extensions and splitters.
Find us on:
CAN (866) 766-3426 | aquascapeinc.com
• The power cable should be protected
at all times to avoid punctures, cuts,
bruises, and abrasion.
• Operating the light fixture outside of the
10.8-15 volt operating range voids the
product warranty and may damage or
shorten the life of the LEDs.
IMPORTANT: Aquascape, Inc.
is not responsible for losses,
injury, or death resulting
from a failure to observe these safety
precautions, misuse or abuse of pumps
or equipment.
LED Color-Changing Lighting Specs
LED Color-Changing Fountain Light
1.5" diameter x 2.5"H
10.8V-15V
2.5±10%
20 lm (white)
3,000 K (white)
70 (white)
30°
15'
Ex. 2
facebook.com/AquascapeInc
youtube.com/aquascape4
twitter.com/AquascapeInc
Ex. 3
Ex. 4