Samsung DVD-C450K Mode D'emploi page 5

Note
- Noise may be generated if the audio cable is placed too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection section below.
- The number and position of terminals can vary depending on your TV set.
Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal
of the DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the
Video Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN ).
B. Connection to an Audio System (2 Channel Amplifier, Dolby
Digital,MPEG2 or DTS Amplifier)
- Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the
DVD player to the AUDIO (red and white) IN terminals of the Amplifier. If using a coaxial cable,
connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the
DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
- Using the video signal cable(s), connect the VIDEO or COMPONENT terminals on the rear of the
DVD player to the VIDEO or COMPONENT terminals of your TV.
- Turn on the DVD player, TV, and Amplifier.
- Press the input select button of the Amplifier to select external input in order to hear sound
from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's audio input.
C. Connections to a TV Interlace / Progressive
- Using Component video cables (not included), connect the COMPONENT VIDEO OUT (PR, PB
and Y) jacks on the rear of the DVD player to the COMPONENT IN (PR, PB and Y) jacks of your
TV.
- Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the
DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV.
- Set the Video Output to I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO
SEL. button to change the Video Output mode.
- Press the input selector on your TV remote control until the Component signal from the DVD
player appears on the TV screen.
- Set the Video Output to I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO
SEL. button to change the Video Output mode.
Note
- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace
output method has. Progressive scanning method can provide better and clearer picture quality.
DVD-C450K
DVD-C450
DVD-C360
DVD-C350K
DVD-C350
COAXIAL CABLE
WHITE
BLUE GREEN
RED
A
VIDEO CABLE
AUDIO CABLE
C
YELLOW
WHITE
RED RED BLUE GREEN
RED
YELLOW
DVD-C370
COAXIAL CABLE
blue
red white yellow
A
VIDEO CABLE
AUDIO CABLE
C
red white
yellow
red blue green
D. Connection to a 5.1CH Analog
Amplifier (ONLY DVD-C370)
- If using audio cables for 5.1 CH Analog Amplifier (not
included) connect the 5.1CH ANALOG AUDIO OUT
terminals on the rear of the DVD player to the 5.1CH
ANALOG AUDIO IN terminals of the 5.1CH Analog
Amplifier.
- Using the video signal cable(s), connect the VIDEO
or COMPONENT terminals on the rear of the DVD
player to the VIDEO or COMPONENT terminals of
your TV as described on pages.
- Turn on the DVD player, TV, and Amplifier.
- Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD
player.
2-Channel stereo ampilfier,
RED WHITE
Dolby digital or
B DTS amplifier
AUDIO CABLE
WHITE
RED
COMPONENT CABLE
Do not use the connection red white
B
Scart and Component Video
(Y.Pb,Pr) Simultaneously
green
Audio Cable
red white
COMPONENT CABLE
Red White Black
Red White Black
Red White Black
D
5.1Ch Analog-
Amplifier
Red White Black
5