Installation; Start-Up And Use - Hotpoint Ariston BDC M45 Série Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18

Installation

GB
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on the
bottom left side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated
on the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these safety
measures not be observed.

Start-up and use

Starting the appliance
! Before starting the appliance, follow the installation
instructions ( see Installation ).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
1. Insert the plug into the socket and ensure that the internal
light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an average
value. After a few hours you will be able to put food in the
refrigerator.
14
Setting the temperature
The temperature inside the refrigerator compartment
automatically adjusts itself according to the position of the
thermostat knob.
1 = warmest
5 = coldest
We recommend, however, a medium position.
The cooling section of the refrigerator is located inside the back
wall of the refrigerator compartment for increased space and
improved aesthetics. During operation, the back wall will be
covered in frost or water droplets depending on whether the
compressor is operating or paused. Do not worry, the refrigerator
is functioning normally.
If the TEMPERATURE ADJUSTMENT knob has been set on high
values with large quantities of food and with a high ambient
temperature, the appliance can operate continuously, resulting in
excessive frost formation and excessive energy consumption:
compensate for this by shifting the knob towards lower values
(defrosting will occur automatically).
PURE WIND
It is recognizable due to the presence of the mechanism on the
top part of the refrigerator compartment (see diagram).
B
A
Pure Wind maximises air circulation, improving the efficiency of
the evaporator and helping to achieve the optimal temperature
inside the refrigerator as quickly as possible each time it has
been opened. The blown air (A) is cooled when it comes into
contact with the cold wall, whereas the hotter air (B) is sucked up
(see diagram).
SHELVES: with or without grill.
Due to the special guides the shelves are removable and the
height is adjustable (see diagram), allowing easy storage of
large containers and food. Height can be adjusted without
complete removal of the shelf.
MULTI-USE bin: to store food (such as cold meats) for a long
time and also prevent odours from lingering in the refrigerator.
It can be removed for use and it may be shifted sideways to
optimise space (see diagram).
B
B
A

Publicité

Table des Matières
loading

Table des Matières