HIKVISION DS-PD1-EB-WS2 Mode D'emploi

DS-PD1-EB-WS2
Wireless Panic Button
Diagram References
1
Appearance Description
2
Register Panic Button
Register Panic Button Locally
Please register the device within 90 seconds after it being powered on.
Register Detector
1.Make the security control panel enter the register mode.
2.Register the panic button: Hold any one of the buttons until the two LEDs
flash alternately. The green LED will flash 8 times if the registration is finished.
3.Communication Test: Hold both of the buttons for 2s to trigger the alarm.
Note: The distance between the security control panel and the detector
should be less than 50 cm.
Initialize the Detector
1. Remove the battery to power the panic button off.
2. Hold any of the buttons and reinstall the battery to power the detectoron
at the same time. Release the button while the two LEDs flash once together.
When the initialization is completed, the indicator turns to alternately
flashing red and green.
Register Panic Button Via APP
1. Log in to the APP Store and input" Hik-Connect" to search the mobile
client. Download and install Hik-Connect to your phone.
2. After installing, tap to run the client.
3. Power on the security control panel.
4. Log in the Hik-Connect and tap the icon"+" at the upper-right coner of the
Hik-Connect page to add the security control panel. You can scan the QR code
on the device rear panel or on the package box, or input the device serial No.
manually to add the device when the device is in the registration mode.
5. After adding the security control panel, tap the alarming status icon on the
right of the security control panel's name to enter the Partition page.
6. Tap the"+" icon on Partition page to add the peripherals.
3
LEDs: General LEDs
D
(i) From power up: Not registered
(ii) Registration process
(iii) 8 x Flashed: Registered
(iv) 18 x Slow flashes: Fault with new battery installed
(v) Panic alarm has been activated
(vi) Control panel has not received the signal from HUD
Specification
Setting devices technical characteristics
Hold-up function Yes
LED indication Red, Amber, Green
Two-way wireless technology Yes
Two-way wireless technology
One push to learn Yes
Transmission method Fully encrypted rolling code
Environmental and operating features
Operation temperature -10°C to +40°C(Certified)
Dimensions(H x W x D) 70 x 30 x 20 mm
Electrical ＆ battery
Transmission frequency 433MHz, FM transceiver
Range in open space 300m
Battery type CR1/3N
Battery voltage 3.0 V
Threshold 2.1V +/- 5%
Battery Information
The battery supplied has been chosen to provide long service life
whilst, for safety reasons, having limited output current.
When disposing of the product, the battery must be removed and
disposed of separately in accordance with the local regulations.
1
Appearance
Indicator
Panic Button
Panic Button
3
G
R R
(i) Slow flashing (ii) Fast flashing
Product Information
User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties
of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
"Hikvision"). This user manual (hereinafter referred to be "the Manual") cannot be reproduced,
changed,translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This manual is applicable to detector.The Manual includes instructions for using and managing
the product. Pictures, charts, images and all other information hereinafterare for description and
explanation only. The information contained in the Manual is subject to change, without notice,
due to firmware updates or other reasons.
Please find the latest version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision's trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Hangzhou Hikvision Digital Technology CO.,Ltd.
R=Red G=green
G
R
G
G
(iii)
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and
your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
2
G
R
R
(iv) (v)
G
(vi)